Specifications - Interlogix GS320 serie Installationsanleitung

Wiring
See Figure 3.
Connecting cable:
•
1 to 4: tinned copper
•
5 (Red): +
• 6 (Blue): −
Before connecting, the wires must be electrically checked. The
opposite wires are always connected, you can check the
resistance 0 Ω between them. For multiple detector
connection, you can use two adjacent wires as an input, and
the other two as an output, disregarding the direction. See
Figure 4 for an example.
Testing
The function of the glass break detector can be tested after the
installation with the test set GS331.
Optional accessories
•
GS303: Glass break detector adhesive set with cleaning
towels
•
GS331: Glass break detector tester

Specifications

Mounting Surface
Indication LED
Housing bottom Ceramic substrate
Voltage 9 to 18 V
Voltage ripple, p-p 1,0 V max.
Current consumption about 0,6 mA / about 5 mA
(standby/triggered)
Switching current 200 mA max.
Switching power 0,3 W max.
Reset voltage 2,2 V max.
Reset time 10 ms min.
about 5 Ω
Contact resistance
Contact capacity about 10 nF
Floating limit 50 V
LIYY 6X 0,14 mm² tinned copper
Connecting cable
4X black, 1X red (+), 1X blue (−)
Inner conductor
Ø3,8 mm (<10 m authorized by VdS)
Cable dimensions
GS320 2 m
GS321 6 m
GS322 20 m
Housing dimension 37 x 19 x 12 mm
Housing material S-B
Colour White
−40 to +70°C
Operating temperature
Glass types
Flat glass (6 mm), security glass (ESG)
(6 mm), insulating glass (4 mm)
Glass size per detector 40 x 40 cm min., 200 x 100 cm max.
Protection category VdS environmental class III A
IP rating IP 67
2 / 10
Regulatory information
Manufactured for UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092, USA
AUTHORIZED EU REPRESENTATIVE:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Product warnings THESE PRODUCTS ARE INTENDED FOR SALE
and disclaimers TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY "AUTHORIZED
DEALER" OR "AUTHORIZED RESELLER", IS
PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-
warning/
Certification
European Union UTC Fire & Security hereby declares that this
directives device is in compliance with the applicable
requirements and provisions of the Directive
2014/30/EU and/or 2014/35/EU. For more
information see www.utcfireandsecurity.com or
www.interlogix.com.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.utcfssecurityproducts.eu/recycle/
Contact information
www.utcfireandsecurity.com or www.interlogix.com
For customer support, see www.utcfssecurityproducts.eu
DE: Installationsanleitung
Beschreibung
Der Glasbruchsensor überwacht ebene Glasflächen innerhalb
eines Radius von max. 2 m. Der Überwachungsradius ist
abhängig von der Glasscheibenstärke, den
Alterungszuständen der Glasscheibe, der
Glasscheibenrahmung (Metall, Kunststoff, Holz) und der
Glasscheibenkittung (Glaskitt, Silikon).
Glasbrüche, deren mechanische Schwingungen den
Glasbruchsensor nicht in der entsprechenden Frequenz und
Amplitude erreichen, führen zu keiner Auslösung. Das Ritzen
der Glasscheibe mit einem Glasschneider wird nicht als
Glasbruch erkannt.
Der Glasbruchsensor wird von der Zentrale mit 12 V DC
versorgt. Im nicht ausgelösten Zustand beträgt die
Stromaufnahme pro Glasbruchsensor ca. 0,6 mA. Der
elektronische Schalter ist hierbei geschlossen, öffnet aber bei
Ausfall der Stromversorgung.
P/N 1078283 (ML) • REV D • ISS 11MAR19
or scan the QR code.