Makita DJV142 Bedienungsanleitung Seite 7

Low battery voltage:
•
The remaining battery capacity is too low
and the tool will not operate. In this situation,
remove and recharge the battery.
Selecting the cutting action
Fig.3
This tool can be operated with an orbital or a straight
line (up and down) cutting action. The orbital cutting
action thrusts the blade forward on the cutting stroke
and greatly increases cutting speed.
To change the cutting action, just turn the cutting action
changing lever to the desired cutting action position.
Refer to the table to select the appropriate cutting action.
Position Cutting action
Straight line
0
cutting action
Small orbit
cutting action
Medium orbit
cutting action
Large orbit
cutting action
006376
Switch action
CAUTION:
Before inserting the battery cartridge into the tool,
•
always check to see that the switch trigger
actuates properly and returns to the "OFF"
position when released.
Fig.4
To start the tool:
Press the lock switch to turn the tool into standby mode.
It turns the lamp on, too.
Pull the switch trigger to start the tool. Release the
switch trigger to stop.
For continuous operation, pull the switch trigger and
then push in the lock on button.
To stop the tool from the locked position, pull the switch
trigger fully, and then release it.
In standby mode, press the lock switch to turn the lamp
off and turn the tool into lock-off mode.
NOTE:
The lock switch does not actuate during cutting
•
operation.
When the tool is in standby mode, the lamp keeps
•
lighting.
If the tool is left 10 seconds without any operations
•
in standby mode, the tool is automatically turned
into lock-off mode and the lamp goes off.
Applications
For cutting mild steel,
stainless steel and plastics.
For clean cuts in wood
and plywood.
For cutting mild steel,
aluminum and hard wood.
For cutting wood and
plywood.
For fast cutting in
aluminum and mild steel.
For fast cutting in
wood and plywood.
Lighting up the lamps
CAUTION:
Do not look in the lamp or see the source of lamp
•
directly.
To turn on the lamp, press the lock switch.
To turn off the lamp within 10 seconds, press the lock
switch again.
NOTE:
Use a dry cloth to wipe the dirt off the lens of lamp.
•
Be careful not to scratch the lens of lamp, or it
may lower the illumination.
When the tool is overheated, the lamp flickers.
•
Cool down the tool fully before operating again.
Speed adjusting dial
Fig.5
The tool speed can be infinitely adjusted by turning the
speed adjusting dial. You can get the highest speed at 6
and the lowest speed at 1.
Refer to the table to select the proper speed for the
workpiece to be cut. However, the appropriate speed
may differ with the type or thickness of the workpiece. In
general, higher speeds will allow you to cut workpieces
faster but the service life of the blade will be reduced.
Workpiece to be cut
Wood
Mild steel
Stainless steel
Aluminum
Plastics
013925
CAUTION:
The speed adjusting dial can be turned only as far
•
as 6 and back to 1. Do not force it past 6 or 1, or
the speed adjusting function may no longer work.
NOTE:
When the speed adjusting dial is at 3 or higher, the
•
tool automatically reduces the no-load speed to
reduce the vibration under no-load. Once the tool gets
load, the tool speed reaches the preset speed. Then
the tool keeps the speed until the tool is switched off.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and the
•
battery cartridge is removed before carrying out
any work on the tool.
Installing or removing saw blade
CAUTION:
Always clean out all chips or foreign matter
•
adhering to the blade and/or blade holder. Failure
to do so may cause insufficient tightening of the
blade, resulting in a serious personal injury.
7
Number on adjusting dial
4 - 6
3 - 6
3 - 4
3 - 6
1 - 4