Dry Ironing; Maintenance And Cleaning - TEFAL PRO EXPRESS TOTAL AUTO CONTROL Gebrauchsanweisung

Power Zone Function
• Your appliance includes the Power Zone function: concentrated steam shot at the tip of the soleplate, to be used in
particular to target stubborn creases, detailing and zones that are dificult to access.
• To use this function, press the Power Zone function on top of the iron as often as necessary

Dry ironing

• Do not press the steam control button under the iron handle.
Refilling the tank during use
• When the red «Tank empty» light is lashing
1. Remove the detachable water tank using the handle (located at the front of the steam generator) and ill it without
exceeding the MAX level.
2. Push it back into its housing until you hear a «click».
3. Press the «OK» button located on the control panel until the light goes out to continue ironing.

Maintenance and cleaning

Cleaning your steam generator
Ultragliss soleplate (depending on model):
• While the soleplate is still warm, clean it with a damp non-metallic pad.
Your steam iron is fitted with a Gliss/Glide Protect
on model):
• Its exclusive active coating allows it eliminate any impurities that may be regularly
generated during normal conditions of use.
• Ironing with an unsuitable programme could nonetheless leave traces that require manual
cleaning. In this case, we recommend using a soft damp cloth on the soleplate while it is still
warm to avoid damaging the coating.
• Do not use any type of cleaning or descaling product to clean the soleplate or the base unit.
• We recommend always standing your iron upright or on the iron rest to protect its coating.
• Never hold the iron or the base unit under a running tap.
• Clean the plastic parts from time to time using a slightly damp soft cloth.
Easy descaling of your steam generator
To extend the life of your steam generator and avoid scale on your ironing, your steam
Do not use any descaling
generator is equipped with a built-in scale collector. This collector, located in the tank,
substances (industrial
descaling products
automatically removes the scale that forms inside.
etc.) when rinsing the
anti-scale collector or the
Operation:
boiler tank, they could
• An orange «anti-scale» light located on the control panel starts blinking to tell you that the
damage it.
anti-scale collector needs rinsing - fig.12.
Before emptying your
steam generator, it must
always be left to cool for
2 hours to avoid any risks
been unplugged for at least two hours and has cooled down completely. To carry out
of scalding.
this operation, the steam generator must be close to a sink as water may come out of
the tank when it is opened.
• Once the steam generator has completely cooled down, lift the tab
• Fully unscrew the collector
the tank.
• To clean the collector, simply rinse it under running water to remove any scale it contains
• You can soak the collector rod in white vinegar (available from hardware stores) or lemon juice for a few hours to
remove any stubborn scale stuck to the rod.
• Place the collector in its housing by screwing it in completely to ensure it is watertight but do not overtighten it
- fig.20-21.
• Put the tab back in place
- fig.22.
• Next time you use your appliance, press the «OK» button located below the control panel until the orange
«Anti-scale» light goes out
In addition to this regular maintenance, it is advisable to rinse the tank out completely every 6 months or after
approximately 25 uses, whichever is the sooner.
fig.11, there is no more steam. The water tank is empty.
-
TM
Important: This operation must not be carried out unless the steam generator has
and pull it out of the base unit
- fig.17
- fig.23.
Autoclean soleplate (depending
- fig.16.
fig.18, it contains the scale that has built up in
-
20
- fig.15.
Never use harsh or
abrasive cleaning
products.
Warning! Using an
abrasive pad will damage
the soleplate's autoclean
coating - fig.27.
- fig.19.