Operating The Appliance - LUND 67120 Originalanleitung

GB
Do not vacuum fi ne dust, e.g. fl our, gypsum, printer toner, etc. Do not use the vacuum cleaner for cleaning industrial waste, e.g.
sawdust, debris, metal fi lings, etc.
The vacuum cleaner must not be used in a dust extraction system where the dust is generated during operation of other tools,
e.g. grinding, cutting, polishing, etc.
When vacuuming, static charges may occur on the appliance. This is normal, especially when cleaning in low humidity conditions.
In order to minimise this phenomenon, it is necessary to periodically touch the grounded, metal objects around the house, e.g.
radiators, with the pipe and to increase the humidity in the room to be cleaned.

OPERATING THE APPLIANCE

CAUTION! Turn off the appliance and unplug the power cord from the socket during all equipment assembly and disassembly
activities.
Appliance assembly and disassembly
Take the vacuum cleaner, the dust container and accessories out of the packaging and remove all packaging components. Install
the dust container.
Before fi rst use, make sure that the container has all components and is correctly assembled.
If the container is mounted on a vacuum cleaner, it must be removed. Slide the lock lever with your fi nger and then remove the
container from the vacuum cleaner (II).
Remove the internal paper fi lter from the container (III) and then the external plastic fi lter (IV). The fi lters have properly shaped
guides, which facilitate the correct installation of the fi lters in the container (V). Check the condition of each fi lter and the condition
of the gasket in the paper fi lter base to ensure that no components are damaged. The container has a snap-on lid on the front,
make sure it is closed. The lid is opened by pulling back the latch (VI).
Attach the container with the closed lid and the installed fi lters to the vacuum cleaner. Lock the recess in the container's bottom
part onto the housing hook (VII) and then snap the rear part of the container into the housing.
A correctly installed container cannot be removed otherwise than by pulling back the lock lever.
Installation of accessories
Insert the pipe or the crevice brush into the opening in the vacuum cleaner housing underneath the dust container (VIII).
The pipe has electrical contacts which are used to transfer power to the turbo brush. The pipe must be installed in such a manner that
the contacts reach the socket and the lock snaps into place to prevent unintentional disconnection of the pipe, and the ratchet mech-
anism can be heard. The pipe can be disconnected by lifting and holding the lock latch and then pulling the pipe out of the opening.
The crevice brush does not require electrical connection and locking.
Fix the selected brush at the other end of the pipe (IX). Mounting is done by sliding the end of the pipe into the inside of the opening
or brush. Similarly to the installation of the pipe, care must be taken to ensure that the brush is electrically connected and locked.
The brush is disconnected in the same manner as the pipe.
Purpose of the accessories
Pipe - a fi xed-length pipe which allows you to extend the length of the vacuum cleaner, making it possible to clean larger areas
comfortably. The pipe is also used to power the turbo brush.
Turbo brush - universal brush for cleaning both carpets and all types of hard fl oors. Thanks to the additional rotating brush it is
possible to eff ectively clean hair and fur entangled in the carpet pile.
3 in 1 crevice brush - allows for cleaning in narrow crevices. The brush is equipped with a double-sided cover with long and short
bristles. Slide the cover onto the end of the brush so that the cover opening locks with the brush latch (X).
Docking station - allows you to set the vacuum cleaner on the fl oor during storage. The charger plug can be attached to the base
of the station as shown in the picture (XI). If the charger is plugged into a socket, placing the vacuum cleaner in the station will
cause the battery to begin charging automatically. The docking station also allows the attachment of a turbo brush, the pipe and
the crevice brush (XII).
Charging the Battery
Make sure that the battery is correctly installed in the vacuum cleaner. Slide the battery with a part of its housing into the battery
compartment (XIII), then slide it in completely into the battery compartment and secure it with the latch.
Plug the charger plug into the vacuum cleaner charging socket (XIV) or slide the vacuum cleaner into the docking station with the
charger plug installed.
The charge indicator will light up LEDs successively. Initially, the LED lights pulsate and then change to a constant light. The
charging is completed if all three LEDs are lit up constantly. The vacuum cleaner should be under supervision throughout the
charging process. Immediately after charging is complete, disconnect the charger from the mains and the vacuum cleaner from
the charger. If a docking station is used for charging, disconnect the charger from the mains.
WARNING! Leaving the vacuum cleaner with a fully charged battery connected to the charger will lead to irreparable
damage to the battery and may cause fi re or electric shock.
It is not possible to use a vacuum cleaner for cleaning while charging the battery.
O R I G I N A L I N S T R U C T I O N S
12