Maintenance Advice - Chicco NEXT2ME Bedienungsanleitung

make sure that all of the fasteners have been correctly attached
and that the zips are closed and locked right to the end of their
travel. WARNING: do not use the cot with adjustable feet par-
tially or totally rotated and unlocked (fig. 11). The correct posi-
tion for use is illustrated in figure 12. In the case of accidental
knocks against adjustable feet, return them to the correct posi-
tion by lifting the crib slightly.
HEIGHT ADJUSTMENT OF THE COT
The crib can be adjusted to different height positions. In order
to adjust the height, pull the adjustment lever upwards and lift
the crib to the desired position (fig. 13). Repeat this operation
on the opposite side.
The base of the crib can be inclined slightly by adjusting the
2 legs to different heights (fig. 14). WARNING: the crib can be
inclined with a maximum variance of 2 positions between one
leg and the other (for example: the right leg in position 3 and
the left leg in position 1, see fig. 15). WARNING: The head of the
child should always be positioned on the highest side (fig. 16).
CO-SLEEPING MODE (FIXING TO THE BED)
The crib can be fixed to the parent's bed (co-sleeping mode).
WARNING – IMPORTANT FOR THE SAFETY OF YOUR CHILD: this
method is only possible with bed types that comply with all of
the conditions described in this paragraph.
In particular the side support of the crib should always be put
close to the parent's mattress and the mattress should always
be aligned with the height of the side support for restraint of
the crib (see fig. 17). Furthermore, the crib should be firmly
fixed to the structure of the parents bed or to the mattress sup-
port (net or slats).
WARNING: Check to make sure that the crib in the co-sleeping
mode does not interfere with the parent's bed.
WARNING: During use, make sure that the parents bed sheets,
blankets etc. do not enter and cover the interior of the crib.
8. Open the side of the crib with the window using the side zips
and open them completely (fig. 18).
9. Then press the removable tubular structure release button
and remove partially on one side and then on the other (fig.
19). Once this operation has been performed on both sides,
remove the tube and fix it to the legs of the structure using
the relative supports (fig. 20). WARNING: use the crib with the
tube lowered, only in the co-sleeping mode.
10. Move the crib close to the parent's bed and check the height
of the crib compared with the mattress of the bed. WARN-
ING: the height of the parent's mattress should always be
more than that of the side support for containment of the
crib (fig. 21). WARNING: in the co-sleeping mode the 2 legs
of the crib should always be adjusted to the same height.
11. In order to fix the crib to the parents bed (co-sleeping
mode) use the pair of straps provided. The straps can be
found in the lower pocket of the fabric lining (fig. 22).
12. Fix the grey buckles underneath the fabric lining on both
sides. Make sure that the red buckles are positioned above
the strap belt as illustrated in figure 23.
13. Subsequently fix the belt around the structure of the par-
ent's bed, from the bottom towards the top (fig. 24) and fix
the red buckle to form a loop (fig. 25). Repeat this operation
on the other side. For easier installation, during fixing of the
buckles, we suggest that the crib is kept at a short distance
from the parent's bed.
14. At this point, move the crib to the side of the parent's bed
and tighten the loop by pulling the belts firmly (fig. 26). Car-
ry out this operation on one side and then on the other side,
adjusting the belts until the crib is firmly in contact with the
parents mattress. WARNING: before every use always check
to make sure that there is no space between the parent's
mattress and the side of the crib. If there is, pull the belts
firmly to tighten until there's no space and the permitted
condition of use has been restored.
15. Store any excess of belts inside the pocket positioned on
the bottom of the fabric lining.
16. Lock the wheels of the crib as described in point 7.
If, during the fixing operations of the crib to the parent's bed,
it is not possible to slide the feet of the crib under the parent's
bed, it is still possible to fix the crib following the operations
described in the previous points by rotating the adjustable feet
during alignment of the crib to the bed.
In order to rotate the feet pull the rotation release button using
one hand and turn the feet of the crib inward (fig. 27).
WARNING: Use of the product is only permitted with beds
and/or mattresses with straight sides. Use of the product with
round beds and/or mattresses or water beds is not permitted.
WARNING: When the product is used in the "Co-Sleeping Mode"
(fixing to the bed, it should always be fitted to the long side of
access to the bed. DO NOT fix the product to the head or bot-
tom of the bed.

MAINTENANCE ADVICE

The crib and the mattress have a resistant fabric cover, which is
completely removable and washable.
The removal/application activities should be carried out by
adults only. On a regular basis check the condition of the prod-
uct and the presence of any possible damage. In the case of
damage do not use it and keep it out of the reach of children.
For washing of the fabrics, carefully comply with the instruc-
tions indicated on the label.
For cleaning do not use solvents, abrasive products or aggres-
sive products.
Hand wash in cold water
Do not bleach
30° C
Do not tumble dry
Do not iron
Do not dry clean
After each wash check the resistance of the fabric and of the
stitching.
WARNING: During the removal and/or application of the lining,
handle the fabric carefully in order to avoid accidental damage
or tears.
WARNING: the removal and/or application operations may take
a few minutes and should be carried out by an adult.
MAKING THE BED
It is possible to unfasten the crib from the parents' bed in order
to make the bed easily. Just unfasten the grey buckles located
below the fabric finish.
To re-secure the crib to the parents' bed, pull once again the
belts to make sure the crib is properly and firmly secured to
the parents' bed. Pay attention to follow all the steps previously
mentioned in paragraph ''co-sleeping mode (Fixing to the bed)'' .
REMOVABLE LINING
17. Remove the mattress and release the buttons on the lower
part of the fabric structure (fig. 28).
18. Press the buttons located on the legs' fastening point (fig.
29) and pull the upper tubular structure upward, remov-
22
19
20
DI
Th
sup
op
lin
the
WA
Th
no
for
Th
cau
Fo
fer
co