Functional Description; Operation; Maintenance; Optional Accessories - Makita JS1000 Betriebsanleitung

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
the switch lever actuates properly and returns to the
"OFF" position when the rear of the switch lever is
depressed.
• Switch can be locked in "ON" position for ease of oper-
ator comfort during extended use. Apply caution when
locking tool in "ON" position and maintain firm grasp on
tool.
To start the tool, slide the switch lever toward the "I (ON)"
position. For continuous operation, press the front of the
switch lever to lock it.
To stop the tool, press the rear of the switch lever, then
slide it toward the "O (OFF)" position.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
For JS1601 Only
Adjusting the blade clearance (Fig. 2 & 3)
Adjust the clearance between the side blade and the
center blade according to the thickness of the workpiece.
First use a hex wrench to loosen the screw.
Then use the hex wrench to adjust the clearance by tight-
ening or loosening the bolt. There may be a slight differ-
ence between clearances of both sides of the center
blade.
Check the smaller clearance with the thickness gauge
and adjust it.
When using the thickness gauge to adjust the blade
clearance, refer to the table.
Workpiece thickness (mm)
Less than 0.8
0.8 – 1.3
More than 1.3
After adjusting the clearance, tighten the screw securely.
Storing hex wrench (Fig. 4)
Store the hex wrench as shown in the figure when not in
use.
4
Marking on thickness
gauge
0.5
1.0
1.5

OPERATION

Lubrication (Fig. 5)
Before operation, lubricate the contact point of the center
blade and the pin. To keep good cutting performance,
also use a cutting lubricant from time to time during oper-
ation.
Operation (Fig. 6 & 7)
Always hold the tool firmly with one hand on housing. Do
not touch the metal part.
Turn the tool on and set front ends of the side blades on
the workpiece. Now simply move the tool forward, keep-
ing the side blades flush with the workpiece surface.
NOTE:
• When cutting a small portion of the workpiece, you may
have difficulty completing the end of the cut. In that
case, try to cut it again, pulling the workpiece back
slightly.

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Center blade
• Side blade R
• Side blade L
• Hex wrench
• Thickness gauge
NOTE:
• Some items in the list may be included in the tool pack-
age as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to EN62841-2-8:
Sound pressure level (L
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 80 dB (A).
NOTE:
• The declared noise emission value(s) has been mea-
sured in accordance with a standard test method and
may be used for comparing one tool with another.
• The declared noise emission value(s) may also be
used in a preliminary assessment of exposure.
ENG104-2
): 77 dB (A)
pA
ENG907-1