Specifications; Additional Safety Rules - Makita HM1140C Betriebsanleitung

ENGLISH
1 Bit grease
2 Bit shank
3 Tool holder cap
4 Tool holder cover
5 Cut in bit shank
6 Notch in tool holder cap
7 Change ring
8 Side handle
9 Can be swung 360° on the
vertical and secured at any
desired position

SPECIFICATIONS

Model
Blows per minute ........................................1,300 – 2,650
Overall length ..................................................... 517 mm
Net weight ...............................................................6.3 kg
• Due to the continuing program of research and devel-
opment, the specifications herein are subject to change
without prior notice.
• Note: Specifications may differ from country to country.
Power supply
The machine should be connected only to a power sup-
ply of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
Safety hints
For your own safety, please refer to enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses
and/or face shield. It is also highly recom-
mended that you wear a dust mask, ear protec-
tors and thickly padded gloves.
2. Be sure the bit is secured in place before opera-
tion.
3. Under normal
designed to produce vibration. The screws can
come loose easily, causing a breakdown or acci-
dent. Check tightness of screws carefully before
operation.
4. In cold weather or when the machine has not
been used for a long time, let the machine warm
up for several minutes by operating it under no
load. This will loosen up the lubrication. Without
proper warm-up, hammering operation is diffi-
cult.
5. Always be sure you have a firm footing.
Be sure no one is below when using the machine
in high locations.
6. Hold the machine firmly with both hands.
7. Keep hands away from moving parts.
8. Do not leave the machine running. Operate the
machine only when hand-held.
9. Do not point the machine at any one in the area
when operating. The bit could fly out and injure
someone seriously.
Explanation of general view
10 Secures at eight different
positions back and forth
on the horizontal
11 Clamp nut
12 Loosen
13 Tighten
14 "ON I" button
15 ON
16 OFF
HM1140C
operation, the machine
10. When chipping into walls, floors or wherever
"live" electrical wires may be encountered, DO
NOT TOUCH ANY METAL PARTS OF THE
MACHINE!
Hold the machine by the insulated grasping sur-
faces to prevent electric shock if you chip into a
"live" wire.
11. Do not touch the bit or parts close to the bit
immediately after operation; they may be
extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing bit
Important:
Always be sure that the machine is switched off and
unplugged before installing or removing the bit.
This machine accepts 3/4" Hexagonal and 21/32" round
shank bits. Clean the bit shank and apply the bit grease
provided to it before installing the bit. (Fig. 1)
Pull the tool holder cover down all the way. (Fig. 2-1)
With the cut in the bit shank aligned with the notch in the
tool holder cap, insert the bit into the tool holder. (Fig. 2-2)
Release the tool holder cover. It will return automatically to
its original position to secure the bit. (Fig. 2-3)
After installing, always make sure that the bit is securely
held in place by trying to pull it out.
is
To remove the bit, pull the tool holder cover down all the
way and pull the bit out.
Bit angle (Fig. 3)
The bit can be secured at 12 different angles. To change
the bit angle, slide the change ring forward, then turn the
change ring to change the bit angle. At the desired angle,
slide the change ring back to the original position. Then
turn the change ring slightly so that the bit will be secured
in place with a little click.
Side handle (auxiliary handle) (Fig. 4)
The side handle can be swung 360° on the vertical and
secured at any desired position. It also secures at eight
different positions back and forth on the horizontal. Just
loosen the clamp nut to swing the side handle to a
desired position. Then tighten the clamp nut securely.
17 Adjusting dial
18 Screwdriver
19 Rear cover
20 Screws
21 Brush holder cap
22 Socket wrench
23 Crank cap
24 Hammer grease
5