Intended Use; Special Safety Instructions - Ayce 2717 Gebrauchsanweisung

INTENDED USE

The machine is intended for sanding, sawing, scraping and cutting on wood,
plasterboard, soft plastics and metals.

SPECIAL SAFETY INSTRUCTIONS

1. WARNING. Contact with or inhalation of harmful / toxic dusts arising from
sanding lead-based painted surfaces, woods and metals can endanger the
health of operator and bystanders.
2. All persons entering the work area must wear an approved mask specially
designed for protection against harmful / toxic dusts, in addition to using the
dust extraction facility, and keeping work area well ventilated.
3. Children and pregnant women must not enter the work area.
4. Do not eat, drink or smoke in the work area.
5. Any pre 1960 building may have paint containing lead on wood or metal
surfaces. If you suspect work-piece contains lead seek professional advice.
6. Some wood and wood type products especially MDF (Medium Density
Fiberboard) can produce dust that can be hazardous to your health. We
recommend the use of an approved face mask with replaceable filters when
using this machine in addition to using the dust extraction facility.
7. This tool is designed for single handed operation. Adopt a stable distance and
make sure that the mains cable is prevented from coming into contact with the
machine or getting caught up on other objects preventing completion of the
sanding pass.
8. Ensure that you have removed foreign objects such as nails and screws from
the work-piece before commencing sanding.
9. Don't use it for wet sanding, for dry sanding only.
10. Do not scrape wet or dampened materials (e.g. wallpaper) or on moist
surfaces. Penetration of water into the machine increases the risk of an
electric shock.
11. Hold the power tool by insulated gripping surfaces, because the sanding
surface may contact its own cord. Cutting a "live" wire may make exposed
metal parts of the power tool "live" and could give the operator an electric
shock.
12. Where possible, secure smaller work-pieces to prevent them from moving
under the tool.
13. Do not force the tool; let the tool do the work at a reasonable speed.
Overloading will occur if too much pressure is applied and the motor slows
resulting in inefficient sanding and possible damage to the motor.
180731_ayce_2717_IM
14. Only use application accessories in good condition. Do not use them if they are
torn or worn.
15. Do not touch the moving sanding sheet.
16. Do not treat the surface to be worked with solvent-containing fluids. Materials
being heated by the scraping can cause toxic vapors to develop.
17. Exercise extreme caution when handling the scraper accessory. The
accessory is very sharp; danger of injury.
18. Keep your hands away from the cutting area. Do not reach under the material
being cut.
19. The machine shall be used in a covered and dry area. The ambient
temperature shall be included between 15°C and 30°C. The humidity level
shall be less than 60%.
20. The tool must be used only for its prescribed purpose. Any use other than
those mentioned in this Manual will be considered a case of misuse. The user
and not the manufacturer shall be liable for any damage or injury resulting
from such cases of misuse.
21. To use this tool properly, you must observe the safety regulations, the
assembly instructions and the operating instructions to be found in this
Manual. All persons who use and service the machine have to be acquainted
with this Manual and must be informed about its potential hazards. Children
and frail people must not use this tool. Children should be supervised at
all times if they are in the area in which the tool is being used. It is also
imperative that you observe the accident prevention regulations in force in
your area.
22. The same applies for general rules of occupational health and safety.
23. The manufacturer shall not be liable for any changes made to the tool nor for
any damage resulting from such changes.
24. Even when the tool is used as prescribed it is not possible to eliminate all
residual risk factors. The following hazards may arise in connection with the
tool's construction and design:
• Damage to the lungs if an effective dust mask is not worn.
• Damage to hearing if effective hearing protection is not worn.
• Hand-arm vibration syndrome if its use is not adequately managed.
80 81 | GB
GB
180731_ayce_2717_IM