Technical Data; Noise/Vibration Information; Changing The Tool - Berner BP 40-82 C Originalbetriebsanleitung

(3) Planer blade/key compartment
(4) Cutting depth scale
(5) Lock-off button for on/off switch
(6) On/off switch
(7) Belt cover
(8) Screw for belt cover
(9) Changeover lever for chip ejector direction
(10) Planer base plate
(11) V-grooves
(12) Handle (insulated gripping surface)
(13) Blade head
(14) Clamping element for planer blade
(15) Fastening screw for planer blade
(16) HM/TC planer blade
(17) Side cutter block guard
(18) Hex key
(19) Extraction hose (dia. 35 mm)
(20) Chip/dust bag A)
A)
(21) Parallel guide
(22) Locking nut for rebate width setting
(23) Fastening screw for parallel/angle guide
(24) Angle guide A)
(25) Locking nut for angle setting
(26) Fastening screw for rebate depth guide
A)
(27) Rebate depth guide
(28) Parking rest
A) Accessories shown or described are not included
with the product as standard. You can find the com-
plete selection of accessories in our accessories
range.

Technical data

English
Planer
Article number
Rated power input
Power output
No-load speed
Cutting depth
Rebate depth
Max. planing width
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V.
These specifications may vary at different voltages and in
country-specific models.

Noise/vibration information

Noise emission values determined according to
EN 62841-2-14.
14 | English
Typically, the A-weighted noise level of the power
tool is: Sound pressure level 85 dB(A); sound
power level 96 dB(A). Uncertainty K=3 dB.
Wear hearing protection.
Vibration total values a
certainty K determined according to
EN 62841-2-14:
a
The vibration level and noise emission value given
in these instructions have been measured in ac-
cordance with a standardised measuring proced-
ure and may be used to compare power tools.
They may also be used for a preliminary estima-
tion of vibration and noise emissions.
The stated vibration level and noise emission
value represent the main applications of the
power tool. However, if the power tool is used for
other applications, with different application tools
or is poorly maintained, the vibration level and
noise emission value may differ. This may signific-
A)
antly increase the vibration and noise emissions
over the total working period.
To estimate vibration and noise emissions accur-
A)
ately, the times when the tool is switched off or
when it is running but not actually being used
A)
should also be taken into account. This may signi-
ficantly reduce vibration and noise emissions over
A)
the total working period.
A)
Implement additional safety measures to protect
the operator from the effects of vibration, such as
servicing the power tool and application tools,
keeping their hands warm, and organising work-
flows correctly.
Fitting
u
BP 40-82 C

Changing the Tool

102519
W 850
u
W 450
–1
min 14000
mm 0–4.0
Use only original Berner HM/TC planer blades.
mm 0–24
The hard metal (HM/TC) planer blade has two cut-
mm 82
ting edges and can be turned. If both cutting
kg 3.2
edges become blunt, the planer blade (16) needs
to be changed. The HM/TC planer blade must not
be resharpened.
/ II
Removing the planer blade (see figure A)
To turn or replace the planer blade (16), turn the
blade head (13) until it is parallel to the planer
base plate (10).
English ➊ Loosen the two fastening screws (15) using
(triax vector sum) and un-
h
2 2
=7.5 m/s , K=1.5 m/s ,
h
English
Pull the plug out of the socket before carry-
ing out any work on the power tool.
English
Take care when changing the planer blade.
Do not pick up the planer blade by the cut-
ting edges. You may be injured by the sharp
cutting edges.
the hex key (18) for approx. 1−2 turns.
English
1 609 92A 4LM • 1.3.19