Technical Data; Angle Grinder; Noise/Vibration Information - Milwaukee AG 22-180 Originalbetriebsanleitung

TECHNICAL DATA

Rated input ................................................................2100 W .........2200 W...................... 2200 W ....................2100 W .........2200 W
Rated speed ...............................................................8500 min
Grinding disk diameter ................................................180 mm ........180 mm..................... 180 mm ...................230 mm ........230 mm
Thread of work spindle ................................................... M 14 ..............M 14 ......................... M 14 ....................... M 14 ..............M 14
Weight according EPTA-Procedure 01/2003 ..................5,1 kg ............5,1 kg ........................ 5,2 kg .......................5,2 kg ............5,2 kg

Noise/Vibration Information

Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K=3dB(A)) ................................92,5 dB (A) ....94,5 dB (A) ................ 94,5 dB (A) ...............92,5 dB (A) ....94,5 dB (A)
Sound power level (K=3dB(A)) .................................103,5 dB (A) ..105,5 dB (A) .............. 105,5 dB (A) .............103,5 dB (A) ..105,5 dB (A)
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN 60745.
Surface grinding:
Vibration emission value a ...........................................9,9 m/s
h
Uncertainty K= .............................................................1,5 m/s
Disk sanding:
Vibration emission value a ...........................................2,9 m/s
h
Uncertainty K= .............................................................1,5 m/s
Rated input ................................................................2100 W ............. 2200 W .....................2200 W .......................................2200 W
Rated speed ...............................................................6600 min
Grinding disk diameter.................................................230 mm ............ 230 mm ...................230 mm ......................................230 mm
Thread of work spindle ................................................... M 14 ................. M 14 ........................ M 14 .......................................... M 14
Weight according EPTA-Procedure 01/2003 ..................5,4 kg ................ 5,4 kg ......................5,3 kg..........................................5,4 kg
Noise/Vibration Information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K=3dB(A)) ................................92,5 dB (A) ........ 94,5 dB (A) ..............94,5 dB (A) ..................................94,5 dB (A)
Sound power level (K=3dB(A)) .................................103,5 dB (A) ...... 105,5 dB (A) ............105,5 dB (A) ................................105,5 dB (A)
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN 60745.
Surface grinding:
Vibration emission value a ...........................................9,9 m/s
h
Uncertainty K= .............................................................1,5 m/s
Disk sanding:
Vibration emission value a ...........................................2,9 m/s
h
Uncertainty K= .............................................................1,5 m/s
For other applications, e.g. Abrasive Cutting-O Operations or Wire Brushing other vibration values could occur.
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745
and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for di erent applications,
with di erent accessories or poorly maintained, the vibration emission may di er. This may signi cantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched o or when it is
running but not actually doing the job. This may signi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the e ects of vibration such as: maintain the tool and the accessories,
keep the hands warm, organisation of work patterns.
AG 22-180 AGV 22-180 E
110-120 V 220-240 V
-1 ....8500 min -1 ................ 8500 min
2 2
......11,1 m/s ................... 11,1 m/s
2 2
........1,5 m/s ..................... 1,5 m/s
2 ........2,6 m/s 2 ..................... 2,6 m/s
2 2
........1,5 m/s ..................... 1,5 m/s
AGV 22-230 AG 22-230 E
110-120 V 220-240 V
-1 -1
........ 6600 min ...............6600 min
2 2
.......... 11,1 m/s .................11,1 m/s
2 ............ 1,5 m/s 2 ...................1,5 m/s
2 2
............ 2,6 m/s ...................2,6 m/s
2 2
............ 1,5 m/s ...................1,5 m/s

Angle Grinder

AG 22-230
110-120 V 220-240 V
-1 ...............6600 min -1 ....6600 min -1
2 2 2
.................. 9,9 m/s ..... 11,1 m/s
2 2 2
...................1,5 m/s ........1,5 m/s
2 ...................2,9 m/s 2 ....... 2,6 m/s 2
2 2 2
...................1,5 m/s ........1,5 m/s
AGV 22-230 E
-1 -1
..................................6600 min
2 2
....................................11,1 m/s
2 ......................................1,5 m/s 2
2 2
..................................... 2,6 m/s
2 2
......................................1,5 m/s
English
15
GB