Technical Data; Screwdriver Safety Warnings; Specified Conditions Of Use - Milwaukee M18 FSG Originalbetriebsanleitung

TECHNICAL DATA

Screwdriver
Production code
Battery voltage
No-load speed
Torque max.
Tool reception
Screw diameter max.
Screw lenghts
Setting range of depth gauge
Weight according EPTA-Procedure 01/2003 (Li-Ion 2,0 Ah)
Noise information
Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
GB
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 62841
Schrauben: Vibration emission value a
Uncertainty K=
WARNING!
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 62841
and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for di erent applications,
with di erent accessories or poorly maintained, the vibration emission may di er. This may signi cantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched o or when it is
running but not actually doing the job. This may signi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the e ects of vibration such as: maintain the tool and the accessories,
keep the hands warm, organisation of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and speci cations provided with this device.
Failure to follow the warnings and instructions may result in electric
shock, re and/or serious injury.
Save all warnings and instructions for future reference.

SCREWDRIVER SAFETY WARNINGS

Hold the power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring. Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give the
operator an electric shock.
Additional Safety and Working Instructions
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is re-
commended, such as dust mask, protective gloves, sturdy non-slip
footwear, helmet and ear defenders.
Do not machine any materials that present a danger to health (e.g.
asbestos).
When working in walls ceiling, or oor, take care to avoid electric
cables and gas or waterpipes.
English
12
h
Clamp your workpiece with a clamping device. Unclamped workpie-
ces can cause severe injury and damage.
Switch the device o immediately if the insertion tool stalls! Do
not switch the device on again while the insertion tool is stalled,
as doing so could trigger a sudden recoil with a high reactive force.
Determine why the insertion tool stalled and rectify this, paying
heed to the safety instructions.
Possible causes can be:
• it is tilted in the workpiece to be machined
• breakage of the material to be used
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is
running.
Remove the battery pack before starting any work on the appliance.

SPECIFIED CONDITIONS OF USE

The screwdriver is suited for setting dry wall screws when xing
gypsum plaster boards to wood furring or metal furring.
M18 FSG
4580 55 01...
... 000001-999999
18 V
0 - 4500 min
-1
13 Nm
1/4 " HEX
(6,35 mm)
6,0 mm
25 - 55 mm
± 3,8 mm
1,7 kg
71,9 dB (A)
82,9 dB (A)
0,45 m/s
2
1,5 m/s
2