Functional Description - Makita 9566CR Bedienungsanleitung

FUNCTIONAL DESCRIPTION

CAUTION:
Always be sure that the tool is switched off and
•
unplugged before adjusting or checking function on
the tool.
Shaft lock
Fig.1
CAUTION:
Never actuate the shaft lock when the spindle is
•
moving. The tool may be damaged.
Press the shaft lock to prevent spindle rotation when
installing or removing accessories.
Switch action
Fig.2
CAUTION:
Before plugging in the tool, always check to see
•
that the slide switch actuates properly and returns
to the "OFF" position when the rear of the slide
switch is depressed.
To start the tool, slide the slide switch toward the "I (ON)"
position. For continuous operation, press the front of the
slide switch to lock it.
To stop the tool, press the rear of the slide switch, then
slide it toward the "O (OFF)" position.
Indication lamp
For model 9566CVR
Fig.3
For model 9566CR
Fig.4
The indication lamp lights up green when the tool is
plugged. If the indication lamp does not light up, the
mains cord or the controller may be defective. The
indication lamp is lit but the tool does not start even if the
tool is switched on, the carbon brushes may be worn out,
or the controller, the motor or the ON/OFF switch may be
defective.
Unintentional restart proof
The tool does not start with the switch being lock-on even
when the tool is plugged.
At this time, the indication lamp flickers red and shows
the unintentional restart proof device is on function.
To cancel the unintentional restart proof, return the slide
switch to "O(OFF)" position, then release it.
Speed adjusting dial
For 9566CVR
Fig.5
The rotating speed can be changed by turning the speed
adjusting dial to a given number setting from 1 to 5.
Higher speed is obtained when the dial is turned in the
direction of number 5. And lower speed is obtained when
it is turned in the direction of number 1.
Refer to the below table for the relationship between the
number settings on the dial and the approximate rotating
speed.
Number
1
2
3
4
5
006409
CAUTION:
If the tool is operated continuously at low speeds
•
for a long time, the motor will get overloaded and
heated up.
The speed adjusting dial can be turned only as far
•
as 5 and back to 1. Do not force it past 5 or 1, or the
speed adjusting function may no longer work.
The tools equipped with electronic function are easy to
operate because of the following features.
Electronic constant speed control
•
Possible to get fine finish, because the rotating
speed is kept constantly even under the loaded
condition.
Soft start feature
•
Soft start because of suppressed starting shock.
Overload protector
•
When the load on the tool exceeds admissible
levels, power to the motor is reduced to protect the
motor from overheating. When the load returns to
admissible levels, the tool will operate as normal.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and
•
unplugged before carrying out any work on the tool.
Installing side grip (handle)
Fig.6
CAUTION:
Always be sure that the side grip is installed
•
securely before operation.
Screw the side grip securely on the position of the tool as
shown in the figure.
Installing or removing wheel guard (For
depressed center wheel , multi disc / abrasive
cut-off wheel , diamond wheel)
For tool with clamp lever type wheel guard
Fig.7
Fig.8
CAUTION:
The wheel guard must be fitted on the tool so that
•
the closed side of the guard always points toward
the operator.
Loosen the lever on the wheel guard. Mount the wheel
guard with the protrusion on the wheel guard band
aligned with the notch on the bearing box. Then rotate
the wheel guard around 180 degrees. Tighten the lever
8
-1
min (R.P.M.)
4,000
5,000
6,500
8,000
10,000