Maintenance; Ec Declaration Of Conformity - Makita JR3000 Betriebsanleitung

Speed change (For JR3000 only) (Fig. 3)
CAUTION:
Use the speed change switch only after the tool
comes to a complete stop.
To change the tool speed, move the speed change
switch to the "L" position for low speed or the "H"
position for high speed.
High speed: ordinary wood, plys or plastics
Low speed: metals (steel pipe, sheet metal, stainless
or copper)
Switch action (For JR3000) (Fig. 4)
CAUTION:
Before plugging the tool, always check to see that the
switch trigger actuates properly and returns to the
"OFF" position when released.
For tools with lock button
To start the tool, simply pull the trigger. Release the
trigger to stop. For continuous operation, pull the trig-
ger and then push in the lock button. To stop the tool
from the locked position, pull the trigger fully, then
release it.
For tools with lock-off button
To prevent the trigger from being accidentally pulled,
a lock-off button is provided. To start the tool, press in
the lock-off button and pull the trigger. Release the
trigger to stop.
Switch action (For JR3000V) (Fig. 5)
CAUTION:
Before plugging the tool, always check to see that the
switch trigger actuates properly and returns to the
"OFF" position when released.
For tools with lock button
To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger.
Release the trigger to stop. For continuous operation,
pull the trigger and then push in the lock button. To
stop the tool from the locked position, pull the trigger
fully, then release it. A speed control screw is pro-
vided so that maximum tool speed can be limited
(variable). Turn the speed control screw clockwise for
higher speed, and counterclockwise for lower speed.
For tools with lock-off button
To prevent the trigger from being accidentally pulled,
a lock-off button is provided. To start the tool, press in
the lock-off button and pull the trigger. Tool speed is
increased by increasing pressure on the trigger.
Release the trigger to stop. A speed control screw is
provided so that maximum tool speed can be limited
(variable). Turn the speed control screw clockwise for
higher speed, and counterclockwise for lower speed.
Operation
Turn the tool on and wait until the blade attains full
speed. Then press the shoe against the workpiece
and apply pressure to cut the workpiece.
CAUTION:
Excessive pressure that causes bending or twisting
of the blade may snap it.
6
Metal cutting (Fig. 6)
Always use a suitable coolant (cutting oil) when cut-
ting metal. Failure to do so will cause significant
blade wear.

MAINTENANCE

CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Replacement of carbon brushes
(For JR3000 only) (Fig. 7 & 8)
Replace carbon brushes when they are worn down to
the limit mark. Both identical carbon brushes should
be replaced at the same time.
To maintain product safety and reliability, repairs,
maintenance or adjustment should be carried out by
a Makita Authorized Service Center.
For European countries only
Noise and Vibration
The typical A-weighted noise levels are
sound pressure level: 87 dB (A)
sound power level: 98 dB (A)
Uncertainty is 3 dB (A).
– Wear ear protection. –
The typical weighted root mean square acceleration
2
value is 9 m/s .
These values have been obtained according to
EN60745.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product
is in compliance with the following standards of standard-
ized documents,
EN60745, EN55014, EN61000
in accordance with Council Directives, 89/336/EEC and
98/37/EC.
Yasuhiko Kanzaki
MAKITA INTERNATIONAL EUROPE LTD.
Michigan Drive, Tongwell, Milton Keynes,
Bucks MK15 8JD, ENGLAND
Responsible manufacturer:
Makita Corporation Anjo Aichi Japan
ENG006-2-V4
CE 2005
Director
ENH101-5