User Configurations; Operation - Vimar Elvox TAB 7548 Technisches Handbuch

TAB: 7548
default the Master).
5) Adjust the brightness with the
contrast with the or
6) You exit the procedure with a time out (Conversation time) or by hang-
ing up the micro-telephone.
Default data restore procedure
1) Lift the handset and place to the ear.
2) Press the and buttons simultaneously and keep them
pressed until the button starts blinking.
3) Release the buttons.
4) Press and hold down the
5) When an audible warning is emitted (during the sound) release the
button and briefly press the
The indoor unit programming has now been deleted. Make sure that the
programming has been successfully deleted by pressing the
button. The indoor unit should emit an audible warning (3 beeps).

User configurations

These operations are to be done with the indoor unit on standby
and the handset hung up.
Selecting panel call tunes
10 different chime tunes can be selected.
1) Press and hold down the
blinking accompanied by an audible warning.
2) Press button and the internal unit will start playing the last tune
stored.
3) Repeatedly press button
4) Press the button to save the tune or wait 15s. At the end of
configuration, the blinking
Chime volume adjustment
The chime volume can be set to 10 levels.
1) Press and hold down the
starts blinking accompanied by an audible warning.
2) Press button to decrease or
Each time the buttons are pressed the volume changes by one level.
3) After selecting the required volume, press button
level or wait 15s. At the end of configuration, the
blinking.
Muting the chime
To mute the chime, press the
ly 2s). Deactivation is confirmed with a "low-pitched" tone and the
button lighting up with a steady light. Chime reactivation is signalled by a
"high-pitched" tone and the
Adjustments (during a conversation)
Brightness adjustment (10 levels with indoor unit in a
20
and buttons and adjust the
buttons.
button.
button.
button (for 2 s) until the button starts
to select the kind of tune you want.
button goes out.
button (for 2 s) until the
to increase the chime volume.
to store the
button stops
button and hold it down (approximate-
button going out.
conversation)
Adjustment is possible during communications and self-starting, press
the and buttons (underneath the handset) to adjust the bright-
ness.
External call voice unit volume adjustment (10 levels
with indoor unit in a conversation)
Use the and
desired level. A beep is emitted on reaching the maximum or minimum
level.
It is adjusted during a conversation.
Internal call voice unit volume adjustment (10 levels
with indoor unit in a conversation)
Use the and
desired level. A beep is emitted on reaching the maximum or minimum
level.
It is adjusted during a conversation.

Operation

Caution: For the indoor station to work, the ID code must have already
been configured. To check this, press a button on the monitor (but not
the volume and brightness buttons): if an ID has been assigned to the
monitor, one beep will sound, if no ID has been assigned or it has been
deleted, 3 beeps will sound.
Answering a call
A call from the outdoor entrance panel or from an intercommunicating
device can be answered during the chime cycle or once it has ended. To
answer, lift the handset; to end the call, replace the handset.
FP/M Landing calls (see "FP/M connection variant" wir-
ing diagrams)
The duration of the chime cycle depends on how long the button is
pressed, for a maximum time of 10s.
Making an intercommunicating call
To make a call to another indoor unit, one or more buttons must have
button
been programmed (see "Button configuration" section). Raise the hand-
set and press the programmed button for the indoor unit to call. During
the call, the indoor unit emits a tone in order to signal that the call is
being made. If the indoor unit is already engaged with another call, a
tone will be heard on the indoor unit making the call to indicate that the
user receiving the call is busy. When the called party answers, the com-
munication is automatically activated. Hang up to end the conversation.
The maximum length of a conversation is 5 minutes (unless programmed
otherwise with SaveProg).
Temporarily muting the chime (Mute)
When you receive a call, you can temporarily mute the chime by pressing
the button.
Missed call from switchboard (enabled via SaveProg)
If the function is enabled via SaveProg, the LED associated to the
button flashes when a call from the switchboard is missed.
EN
buttons (underneath the handset) to adjust the
buttons (underneath the handset) to adjust the