Makita BTP130 Bedienungsanleitung Seite 8

Standard bolt
N m
(kgf cm)
120
(1224)
M14
100
(1020)
80
M12
(816)
60
(612)
40
(408)
M10
20
M8
(204)
0
1.0 2.0
0
Fastening time
007318
High tensile bolt
N m
(kgf cm)
120
(1224)
M12
100
(1020)
80
M10
(816)
60
(612)
M8
40
(408)
20
(204)
0
0 1.0 2.0
Fastening time
007320
NOTE:
Use the proper bit for the head of the screw/bolt
•
that you wish to use.
When fastening screw M8 or smaller, carefully
•
adjust pressure on the switch trigger so that the
screw is not damaged.
Hold the tool pointed straight at the screw.
•
If you tighten the screw for a time longer than
•
shown in the figures, the screw or the point of the
driver bit may be overstressed, stripped, damaged,
etc. Before starting your job, always perform a test
operation to determine the proper fastening time
for your screw.
CAUTION:
If the tool is operated continuously until the battery
•
cartridge has discharged, allow the tool to rest for
15 minutes before proceeding with a fresh battery.
The fastening torque is affected by a wide variety of
factors including the following. After fastening, always
check the torque with a torque wrench.
(M14)
(M12)
(M10)
(M8)
3.0
(S)
(M12)
(M10)
(M8)
3.0
(S)
1. When the battery cartridge is discharged almost
completely, voltage will drop and the fastening
torque will be reduced.
2. Driver bit or socket bit
Failure to use the correct size driver bit or socket
bit will cause a reduction in the fastening torque.
3. Bolt
Even though the torque coefficient and the
•
class of bolt are the same, the proper
fastening torque will differ according to the
diameter of bolt.
Even though the diameters of bolts are the
•
same, the proper fastening torque will differ
according to the torque coefficient, the class of
bolt and the bolt length.
4. The manner of holding the tool or the material of
driving position to be fastened will affect the
torque.
5. Operating the tool at low speed will cause a
reduction in the fastening torque.
Hammer drilling operation
CAUTION:
There is a tremendous and sudden twisting force
•
exerted on the tool/bit at the time of hole
break-through, when the hole becomes clogged
with chips and particles,
reinforcing rods embedded in the concrete.
To drill in the concrete or tiles, first, turn the action mode
changing lever so that the arrow on the lever points to
the mark on the tool body. The adjusting ring can be
aligned in any torque levels for this operation.
Be sure to use a tungsten-carbide tipped bit.
Position the bit at the desired location for the hole, then
pull the switch trigger. Do not force the tool. Light
pressure gives best results. Keep the tool in position and
prevent it from slipping away from the hole.
Do not apply more pressure when the hole becomes
clogged with chips or particles. Instead, run the tool at
an idle, then remove the bit partially from the hole. By
repeating this several times, the hole will be cleaned out
and normal drilling may be resumed.
CAUTION:
If the tool is operated continuously until the battery
•
cartridge has discharged, allow the tool to rest for
15 minutes before proceeding with a fresh battery.
Screwdriving operation
CAUTION:
Adjust the adjusting ring to the proper torque level
•
for your work.
When driving small wood screws or machine screws. set
the action mode changing lever to the
the adjusting ring to the proper torque level for your
work.
8
or when striking
mark. Adjust