Makita DTW284 Betriebsanleitung Seite 7

NOTE: When the LED display goes off, the tool is
turned off to save the battery power. To check the
remaining batter y c apa c it y , slig h tl y pull t h e s w it c h
trigger.
NOTE: The LED display goes off approximately one
minute a f ter releasing t h e s w it c h trigger.
NOTE: When the LED display lights up and the tool
stops e v en w it h a re c h arge d batter y c artri d ge, c ool
d o w n t h e tool f ull y . I f t h e status w ill not c h ange, stop
using an d h a v e t h e tool repaire d b y a Makita lo c al
ser v i c e c enter.
NOTE: When the tool is overheated, the light flashes
for one minute, and then the LED display goes off. In
t h is c ase, c ool d o w n t h e tool be f ore operating again.
Switch action
Fig.5: 1. S w it c h trigger
CAUTION:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the " OFF " position when released.
To start the tool, simply pull the switch trigger. Tool
spee d is in c rease d b y in c reasing pressure on t h e s w it c h
trigger. R elease t h e s w it c h trigger to stop.
NOTE: The tool automatically stops when you keep
pulling t h e s w it c h trigger f or 3 minutes.
Lighting up the front lamp
CAUTION:
Do not look in the light or see the
source of light directly.
Fig.6: 1. L amp
Fig.7: 1. Button
Changing the impact force/mode
Fig.9: 1. C h ange d in f our steps 2. H ar d impa c t
mo d e 3. Me d ium impa c t mo d e 4. S o f t impa c t
mo d e 5. R e v erse rotation auto stop mo d e
6. Button
You can change the impact mode in four steps: hard,
me d ium, so f t, an d re v erse rotation auto stop mo d e.
To select the step, press the button
Specifications of each impact force grade
Impact force grade displayed
on panel
H ard
Med ium
.
Maximum blows
(/min) Tightening when force and
-1
3,5 00 min
speed are d esired .
(/min) Tightening when you need
-1
2,6 00 min
good c ontrolled pow er.
7 ENGLISH
To turn on the lamp status, press the button
one second. To turn off the lamp status, press the but-
ton f or one se c on d again.
With the lamp status ON, pull the switch trigger to turn on
the lamp. To turn off, release it. The lamp goes out approx-
imatel y 1 0 se c on d s a f ter releasing t h e s w it c h trigger.
With the lamp status OFF, the lamp does not turn on
e v en i f pulling t h e trigger.
NOTE: To confirm the lamp status, pull the trigger.
When the lamp lights up by pulling the switch trigger,
the lamp status is ON. When the lamp does not come
on, t h e lamp status is O F F .
NOTE: U se a d r y c lot h to w ipe t h e d irt o f f t h e lens o f
t h e lamp. Be c are f ul not to s c rat c h t h e lens o f lamp, or
it ma y lo w er t h e illumination.
NOTE: While pulling the switch trigger, the lamp
status c annot be c h ange d .
NOTE: For approximately
t h e s w it c h trigger, t h e lamp status c an be c h ange d .
Reversing switch action
Fig.8: 1. R e v ersing s w it c h le v er
CAUTION:
Always check the direction of
rotation before operation.
CAUTION:
Use the reversing switch only after
the tool comes to a complete stop. C h anging th e d irec -
tion of rotation bef ore th e tool stops may d amage th e tool.
CAUTION:
When not operating the tool, always
set the reversing switch lever to the neutral position.
This tool has a reversing switch to change the direction
o f rotation. D epress t h e re v ersing s w it c h le v er f rom t h e
A side for clockwise rotation or from the B side for coun-
ter c lo c k w ise rotation.
When the reversing switch lever is in the neutral posi-
tion, t h e s w it c h trigger c annot be pulle d .
For approximately one minute after releasing the switch
trigger, t h e impa c t f or c e c an be c h ange d .
H ar d , Me d ium, an d S o f t impa c t mo d e allo w s a tig h ten-
ing suitable to t h e w ork.
The function of reverse rotation auto stop mode works
onl y w it h pulling t h e trigger f ull y in c ounter c lo c k w ise tool
rotation. When the bolt/nut gets enough loosened, the
tool stops t h e impa c t an d rotation.
Application
f or
seconds after releasing
Work
Assembling the steel frame.
Assembling or disassembling
sc af f old s or f ramew ork.