Functional Description - Makita DTW284 Betriebsanleitung

FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
tridge firmly hen installing or removing battery
cartridge. F ailure to h ol d t h e tool an d t h e batter y
cartridge firmly may cause them to slip off your hands
an d result in d amage to t h e tool an d batter y c artri d ge
and a personal injury.
Fig.1: 1. R e d in d i c ator 2. Button 3. Batter y c artri d ge
To remove the battery cartridge, slide it from the tool
w h ile sli d ing t h e button on t h e f ront o f t h e c artri d ge.
To install the battery cartridge, align the tongue on the
batter y c artri d ge w it h t h e groo v e in t h e h ousing an d slip
it into pla c e. I nsert it all t h e w a y until it lo c ks in pla c e
w it h a little c li c k. I f y ou c an see t h e re d in d i c ator on t h e
upper si d e o f t h e button, it is not lo c ke d c ompletel y .
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. I f not,
it may accidentally fall out of the tool, causing injury to
y ou or someone aroun d y ou.
CAUTION:
Do not install the battery cartridge
forcibly. I f t h e c artri d ge d oes not sli d e in easil y , it is
not being inserte d c orre c tl y .
Battery protection system
Lithium-ion battery with star marking
Fig.2: 1. S tar marking
L it h ium-ion batteries w it h a star marking are e q uippe d
with a protection system. This system automatically
cuts off power to the tool to extend battery life.
The tool will automatically stop during operation if the
tool and/or battery are placed under one of the following
conditions:
Overloaded:
The tool is operated in a manner that causes it to draw
an abnormall y h ig h c urrent.
I n t h is situation, turn t h e tool o f f an d stop t h e appli c ation
that caused the tool to become overloaded. Then turn
t h e tool on to restart.
I f t h e tool d oes not start, t h e batter y is o v er h eate d . I n
t h is situation, let t h e batter y c ool be f ore turning t h e tool
on again.
Low battery voltage:
The remaining battery capacity is too low and the tool
w ill not operate. I n t h is situation, remo v e an d re c h arge
t h e batter y .
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
Fig.3: 1. I n d i c ator lamps 2. C h e c k button
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
lig h t up f or f e w se c on d s.
Indicator lamps
Lighted
NOTE: D epen d ing on t h e c on d itions o f use an d t h e
ambient temperature, t h e in d i c ation ma y d i f f er slig h tl y
f rom t h e a c tual c apa c it y .
Indicating the remaining battery
capacity
Country specific
Fig.4: 1. Batter y in d i c ator
When you pull the switch trigger, the LED display shows
the remaining battery capacity. The remaining battery
c apa c it y is s h o w n as t h e f ollo w ing table.
Battery indicator status
On
6 ENGLISH
Off Blinking
75 %
mal f un c tione d .
Remaining battery
capacity
Off
5 0%
20%
0%
Remaining
capacity
to 1 00%
5 0% to 75 %
25 % to 5 0%
0% to 25 %
C h arge th e
battery .
The battery
may h av e
to 1 00%
to 5 0%
to 20%