Makita DDF483 Betriebsanleitung Seite 5

Cordless driver drill safety w arnings
1. Use auxiliary handle(s), if supplied w ith the
tool. Loss of control can cause personal injury.
2. Hold the po w er tool by insulated gripping
surfaces, w hen performing an operation w here
the cutting accessory may contact hidden
w iring. Cutting accessory contacting a live
wire may make exposed metal parts of the power
tool live and could give the operator an electric
s h o c k .
3 . Hold po w er tool by insulated gripping sur-
faces, w hen performing an operation w here
the fastener may contact hidden w iring.
Fasteners contacting a live wire may make
exposed metal parts of the power tool live and
could give the operator an electric shock.
Always be sure you have a firm footing. Be
4 .
sure no one is belo w w hen using the tool in
high locations.
old the tool firmly.
5 .
6. Keep hands a w ay from rotating parts.
7. Do not leave the tool running. Operate the tool
only w hen hand-held.
8 . Do not touch the drill bit or the w orkpiece
immediately after operation ; they may be
extremely hot and could burn your skin.
9 . Some material contains chemicals w hich may
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follo w material supplier
safety data.
10. If the drill bit cannot be loosened even you
open the ja w s, use pliers to pull it out. In such a
case, pulling out the drill bit by hand may result in
injury by its sharp edge.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
w ith product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follo w the safety
rules stated in this instruction manual may cause
serious personal injury.
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
2. Do not disassemble battery cartridge.
3 . If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4 . If electrolyte gets into your eyes, rinse them
out w ith clear w ater and seek medical atten-
tion right a w ay. It may result in loss of your
eyesight.
5 . Do not short the battery cartridge:
( 1 ) Do not touch the terminals w ith any con-
ductive material.
( 2 ) Avoid storing battery cartridge in a con-
tainer w ith other metal objects such as
nails, coins, etc.
( 3 ) Do not expose battery cartridge to w ater
or rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdo w n.
6. Do not store the tool and battery cartridge in
locations w here the temperature may reach or
exceed 50 ° C (122 ° F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely w orn
out. The battery cartridge can explode in a fire.
8 . Be careful not to drop or strike battery.
9 . Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
For commercial transports e.g. by third parties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required.
Please also observe possibly more detailed
national regulations.
Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move
around in the packaging.
11. Follo w your local regulations relating to dis-
posal of battery.
12. Use the batteries only w ith the products
specified by Makita. Installing the batteries to
non-compliant products may result in a fire, exces-
sive heat, explosion, or leak of electrolyte.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will
also void the Makita warranty for the Makita tool and
c h a r g e r .
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Al w ays stop tool operation and
charge the battery cartridge w hen you notice
less tool po w er.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3 . Charge the battery cartridge w ith room tem-
perature at 10 ° C - 40 ° C (50 ° F - 104 ° F). Let
a hot battery cartridge cool do w n before
charging it.
4 . Charge the battery cartridge if you do not use
it for a long period (more than six months).
5 ENGLISH