Warranty; Maintenance - VONROC MS503AC Bersetzung Der Originalbetriebsanleitung

blade along its entire length;
6. Re-tighten the lock nut for 0° bevel angle (44).
Subsequently check the position of the angle indica-
tor (18). If necessary loosen the pointer using a Phi-
lips screwdriver, set to position 0° on the scale for
bevel angle (19) and re-tighten the retaining screw.
Fine-tuning the 45° bevel angle (Fig. Q, S)
1. Adjust the mitre and bevel angle to 45°;
2. Lower the handle (2) and secure it using the
position lock knob (33);
3. Set an angle gauge to 90° and place it on the
table (10), as shown on figure S. The leg of the
angle gauge must be flush with the saw blade
(6) along its entire length;
4. Loosen the lock nut for 45° bevel angle (43);
5. Adjust the stop bolt for 45° bevel angle (27)
until the leg of the angle gauge is flush with the
saw blade along its entire length;
6. Re-tighten the lock nut for 45° bevel angle (43).
Subsequently check the position of the angle indica-
tor (18). If necessary loosen the pointer using a Phi-
lips screwdriver, set to position 45° on the scale for
bevel angle (19) and re-tighten the retaining screw.
Fine-tuning the 0° mitre angle (Fig. T, U)
1. Set an angle gauge to 0° on the table (10) and
position it between the fence (8) and the saw
blade (6);
2. The leg of the angle gauge must be flush with
the saw blade (6) along its entire length;
3. Loosen all four fence bolts (45) and adjust the
fence (8) until the leg of the angle gauge is
flush with the saw blade along its entire length;
4. Retighten all four fence bolts (45) again. Subse-
quently check the position of the angle indicator
(16). If necessary loosen the pointer using a Philips
screwdriver, set to position 0° on the scale for mit-
re angle (15) and re-tighten the retaining screw.

5. MAINTENANCE

Always make sure that the machine is not
connected to the mains electricity when you
carry out any maintenance of the mechanism.
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that the
ventilation openings are free of dust and dirt. Re-
WWW.VONROC.COM
move very persistent dirt using a soft cloth moiste-
ned with soapsuds. Do not use any solvents such
as gasoline, alcohol, ammonia, etc. Chemicals such
as these will damage the synthetic components.
Cleaning the protective guards
Always check the protective guard (4) and retracta-
ble protective guard (5) for debris before using the
machine. Remove old sawdust and splinters using a
brush or similar tool.
Replacing the table insert
Immediately replace damaged table inserts.
With a damaged table insert (12) there is a risk of
small parts getting stuck between table insert and
saw blade, blocking the saw blade. To replace the
table insert:
1. Remove screws of table insert using a Philips
screw driver. If required, adjust mitre and bevel
angle to obtain access these screws;
2. Remove table insert;
3. Install new table insert;
4. Tighten the screws using a Philips screw driver.
ENVIRONMENT
Faulty and/or discarded electrical or
electronic apparatus have to be collected at
the appropriate recycling locations.
Only for EC countries
Do not dispose of power tools into domestic waste.
According to the European Guideline 2012/19/EU
for Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that
are no longer usable must be collected separately
and disposed of in an environmentally friendly way.

WARRANTY

VONROC products are developed to the highest qua-
lity standards and are guaranteed free of defects
in both materials and workmanship for the period
lawfully stipulated starting from the date of original
purchase. Should the product develop any failure
during this period due to defective material and/or
workmanship then contact your VONROC directly.
The following circumstances are excluded from this
guarantee:
EN
17