Inhaltszusammenfassung für Olivetti PF-740
- Seite 1 INSTALLATION GUIDE GUIDE D’INSTALLATION GUÍA DE INSTALACION INSTALLATIONSANLEITUNG GUIDA ALL’INSTALLAZIONE 安装手册 설치안내서 設置手順書 PF-740...
- Seite 3 B(2) J(2) G(4) K (M4x20)(4) H (M4x8)(3) I (12) *I (6) **I (2) E. Clamp ............1 K. S Tite screws M4 × 20 ......4 English F. Wire cover..........1 Be sure to remove any tape and/or cushioning Supplied parts G.
- Seite 4 Procedure 1.Pull out the right cassette (1) and left cas- 3.Remove the lower paper cassette (4) from Be sure to turn the machine main power switch sette (2), remove each of the lift plate stop- the machine. off and disconnect the machine power plug from pers (3) and attach them in the storage 4.Press the release lever(5) and Remove the the wall outlet before starting to install the paper...
- Seite 5 5.Place the machine (8) on the paper feeder 6.Secure the machine (8) to the paper feeder 7.Insert the lower paper cassette (4) into the (A) so that the pins (6) at the front left and (A) with the 2 pins (B). machine.
- Seite 6 9.Remove the screw (12) in the rear of the 10.Remove the screw (14) to remove the metal 11.Fit the hook (16) on the mounting plate (C) paper feeder and remove the cover (13). plate (15). into the opening (17) and then align the 2 positioning projections.
- Seite 7 19 21 13.Pass the power cord (18) through the edging 14.Connect the power cord (22) and the signal 16.Open the lower right cover (26) on the (small) (19) and the signal cable (20) cable (23) to connectors (24) (25) respec- machine.
- Seite 8 H(M4x8) H(M4x8) 17.Open the paper feeder right cover (29). 18.Fit the 3 hooks (30) on the intermediate paper conveying unit (D) into the 3 holes (31) in the guide. 19.Secure the intermediate paper conveying unit (D) with the 2 S Tite screw M4 × 8 (H). NOTICE Be sure to use S Tite screw M4 ×...
- Seite 9 20.Connect the intermediate paper conveying 22.Insert the projection (33) on the wire cover 24.Turn the adjusters on each corner (35) until unit connector (32). (F) into the hole (34) in the paper feeder and they reach the floor and then secure the 21.Attach the clamp (E) and secure the connec- install the wire cover (F).
- Seite 10 K (M4x20) K (M4x20) 25.Select holes (49) and install each stopper (J) with 2 S Tite screws M4 × 20 (K) so that the stoppers will be grounded on the floor. 25.Sélectionner les trous (49) et installer chaque butée (J) avec 2 vis S Tite M4 × 20 (K) de sorte que les butées reposent sur le sol. 25.Seleccione los orificios (49) e instale cada tope (J) con los 2 tornillos S Tite M4 ×...
- Seite 11 Setting the paper size plate and media type Changing paper size (metric specifications 1.Pull out the cassette of the paper feeder. plate only) 2.Turn the front lock lever (36) 90° and remove Insert the paper size plate (G) and media type At shipment, Letter is set for inch models and A4 the front deck cursor (37).
- Seite 12 3.Move the front deck cursor (37) so that it is aligned with the size indicators on the top (39) and 6.Release the hook (41) and remove the deck bottom (38) of the cassette. trailing edge cursor (42). 4.Turn the front lock lever (36) 90° to lock it. 5.Move the rear deck cursor (40) in the same way.
- Seite 13 0.5∼1.5mm 7.Lift up the sub-cursor (43). Adjusting the cursor width 8.Align with the size indicator (44), engage the 1.Load paper in the cassettes. hook (45) and install the deck trailing edge 2.If the gap between the front deck cursor (37) and the paper (46) is outside the 0.5 to 1.5 mm cursor (42).
- Seite 14 3.Insert a Philips-head screwdriver into the 2 long slots (47) in the front deck cursor (37) and loosen 4.Retighten the 2 adjusting screws (48). the 2 adjusting screws (48). Then move the front deck cursor (37). 5.Check that the gap between the front deck cursor (37) and the paper is between 0.5 and 1.5 mm.
- Seite 15 Adjusting the leading edge timing The reference value for the leading edge timing is 20 ±1.5 mm at position (b) in the correct image (a). If the timing is outside this range, perform the fol- lowing adjustment. 1.Set maintenance mode U034, select LSU Out Top and Cassette(L) 2.Adjust the values.
- Seite 16 Adjusting the center line The reference value for the center line is ±0.5 mm or less at position (f) in the correct image (e). If the center line position is outside this range, perform the following adjustment. 1.Set maintenance mode U034, select LSU Out Left and Cassette3 or Cassette4. 2.Adjust the values.
- Seite 17 MEMO...
- Seite 18 MEMO...
- Seite 19 MEMO...
- Seite 20 2012. 9 303NF56714-01...