Troubleshooting - Pioneer PDR555RW Bedienungsanleitung

TROUBLESHOOTING

In case of trouble, first check the following list. What seems to be a failure of the unit is sometimes due to imperfect
maintenance, defective disc or unaccustomed operation. Such troubles are often recovered by correcting simple mistake or
misunderstanding or by simple maintenance operation. If your trouble cannot be recovered after checking the following list,
please call you nearest PIONEER service center or station.
Self-diagnostics
This unit incorporates a self-diagnostic function.
When it detects trouble during an operation, it displays one of the following messages on the display panel.
Display
The disc is stopped due to dirt, stain,
scratch or vibration.
The disc may be loaded upside down.
Alternate display of
"CHECK and "DISC"
A system error occurred perhaps due to
Display blinks
noise or static electricity.
"CHECK"
Information messages related to recording operation
Display
Alternate display of
Digital musical signal containing copy
"CAN NOT" and inhibit signal based on SCMS is being
"COPY". input.
Alternate display of The digital input is interrupted.
"CAN NOT" and
"REC". The data (CD-ROM, etc.) provided cannot
be recorded.
Cyclic display of The source player was already playing
"CHECK", "INPUT"
when the DIGITAL SYNCHRO button
and "CD ?". was pressed.
Alternate display of The unit is making preparations for
"SET" and "UP". recording.
"REPAIR" Because the disc was left in the unit
after recording and the power plug was
unplugged later, the track number and
recording time data have been cleared
without being recorded on the disc.
"REC FULL" No more recording is possible because
the available recording time of the disc
has been used fully or 99 tracks have
already been recorded on the disc.
"Pro DISC" The loaded disc is a CD-R or CD-RW disc
for professional use without "FOR
CONSUMER" indication.
Information messages related to playback operation
Display
A blank disc is loaded.
"NEW DISC"
An attempt is made to play a blank disc.
An attempt is made to start playback
"NO DISC"
without loading a disc.
The unit is resuming an operation. After
"RESUME"
the power supply is cut off by a power
failure or by mistake during recording,
the unit enters RESUME mode so that
additional recording is possible.
108
<PRE1269>
En/Fr En
Cause
Take out the disc and check for dirt, dust, scratch, etc.
Take out and check the disc.
If the same messages are displayed again after the disc is
reloaded, unplug the power cord and plug it in again.
If the same messages are displayed again, please contact a
PIONEER authorized service center.
Unplug the power cord and plug it in again.
If the same messages are displayed again, please contact a
PIONEER authorized service center.
Cause
Record the source through analog input or record copy-
permitted music.
Check if the digital input cable is not disconnected and if the
power of the source player is on.
Check whether the source is a regular music source.
Stop playing the source player.
In a while, "1-SYNC" or "AL-SYNC" is displayed, and the unit
is set to the synchro recording standby mode.
Wait until these messages disappear.
While "REPAIR" is displayed, the track number and recording
time data are repaired by tracking the recorded area. Further
recording or finalization is possible whenever the display
returns to the previous condition.
Tracing of the recorded area takes about 40 minutes if the
disc has been recorded fully.
Replace the disc with a new one.
Erase a CD-RW disc.
Load a CD-R or CD-RW disc with "FOR CONSUMER"
indication.
Take out and check the disc.
Cause
The loaded disc is a blank CD-R or CD-RW disc. Recording is
possible but playback is not.
Open the tray and check if a disc is loaded.
Wait until the message disappears.
Treatment
Treatment
Treatment
Ref. Page
page 18
page 38
Ref. page
page 58
page 20
page 62
page 44
page 48
page 50
page 42
page 78
page 14, 42
Ref. page
page 16
page 38
page 38
page 62
page 76