Important Safeguards - Scarlett SC-1260 Bedienungsanleitung

GB INSTRUCTION MANUAL

IMPORTANT SAFEGUARDS

Please read this instruction manual carefully before
use and keep in a safe place for future reference.
Before the first use of the appliance check that
voltage indicated on the rating label corresponds to
the mains voltage in your home.
For home use only. Do not use for industrial
purposes. Do not use the appliance for any other
purposes than described in this instruction manual.
Do not use outdoors.
Always unplug the appliance from the power supply
before cleaning and when not in use.
To prevent risk of electric shock and fire, do not
immerse the appliance in water or any other
liquids. If it has happened DO NOT TOUCH the
appliance, unplug it immediately and check in a
service center.
Do not take this product to a bathroom or use near
water.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use of the
appliances by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
Do not leave the appliance switched on when not in
use.
Do not use other attachments than those supplied.
Do not operate after malfunction or cord damage.
Do not attempt to repair, adjust or replace any
parts of the appliance. Check and repair the
malfunctioning appliance in the nearest service
center only.
Keep the cord away from sharp edges and hot
surfaces.
Do not place or store the appliance where it can fall
or be pulled into a tub or sink.
Do not pull, twist, or wrap the power cord around
the appliance.
Never insert any objects into openings in the
appliance housing.
Before use, make sure that blades are adjusted
properly.
Do not put operating appliance on any surface, it
may cause injury or damage.
Do not use the appliance with damaged comb, or
with teeth missing from the blades as injury may
occur.
NOTE: KEEP THE BLADES OILED.
Do not use the hair clipper when the skin is
infected.
Do not use the hair clipper on animals.
BLADE ALIGNMENT
Your clipper was carefully examined to ensure that
the blades were oiled and properly aligned before
leaving our factory.
Blades must be realigned if they were removed for
cleaning or after replacement.
To realign the blades, simply match the upper and
lower blades teeth up, point for point.
www.scarlett.ru
End of top blade teeth should be approximately 1.2
mm back from lower blade. Compare your clipper
blades with the sketch (pic.1).
If blade alignment is incorrect, add a few drops of
oil to the blades, switch on the clipper for a few
moments, switch off and unplug. Loosen screws
slightly and adjust. Tighten screws after blade is
aligned.
OILING
To maintain your clipper in peak condition, the
blades should be oiled after every haircut.
Do not use hair oil, grease, oil mixed with kerosene
or any solvent.
BLADE LEVER
The lever located to
the left of the blades,
allows easily adjust cut
hair length while
clipping.
The lever adds versatility to your clipper by
allowing you gradually change the closeness of
your cut without an attachment comb.
When the lever is in the uppermost position, the
blades will give you the closest cut and leave the
hair very short. Pushing the lever downwards
gradually increases the cutting length.
In its lowest position, the lever will leave the hair
approximately the same length as a
comb.
The lever will also extend the use of your blades
since a different cutting edge is used in each
setting.
In addition, if extremely heavy hair cutting has
jammed the blades, it will help you to remove hair
that has become wedged between the two blades
without removing the blades.
While the clipper is running rapidly move the lever
from close cut to longer cut a couple of times.
Do this each time after you have finished using
your clipper to keep the blades free of cut hair.
If this does not help and clipper stops cutting,
blades are dulled. Replace them with new blades.
INSTRUCTIONS FOR HAIR CUTTING
Before starting the hair cut inspect the clipper,
making sure that there is no oil between the cutting
blade teeth, switch the unit on to distribute the oil
between the blade teeth and to check running
smoothness. Wipe off any excess oil. This should
be done after each use. While using the unit,
untwist the cord from time to time to avoid tangling.
Before cutting always comb the hair thoroughly
first.
DETACHABLE COMBS
Attachment comb
1
2
3
4
Each comb attachment is marked accordingly on
its outside middle surface.
To attach a comb, hold it with its teeth upward and
slide onto and along the clipper blade until the front
of the comb firmly seats against the clipper blade.
When you use the clipper for the first time, cut only
small portions of hair.
4
IM003
1 (3mm)
Hair length mm/inches
3 (1/8)
6 (1/4)
9 (3/8)
12 (1/2)
SC-1260