How To Replace The Motion Drive Belt; How To Replace The Mower Drive Belt; How To Install The Wheels; How To Replace The Fuse - Texas A/S 7600E Bedienungsanleitung

How to replace the motion drive belt

REMOVAL OF DRIVE BELT
1. Remove the mower housing. See the instructions on
"How to remove the mower housing".
2. Completely push the pedal forward and engage the
parking brake.
3. Remove the idler pulley (Illustration 30).
4. Loosen the belt guides next to the drive pulley.
5. Remove the motion drive belt from the drive pulley.
6. Remove the motion drive belt from the stack pulley. A
correct replacement part or assistance is available
from an Authorized Service Center in your area.
INSTALLATION OF DRIVE BELT
1. Slide the motion drive belt between the stack pulley
and the belt guides (Illustraton 30).
Install the motion drive belt on the top pulley of the
stack pulley. Make sure the "V" side of the belt is
against the pulley.
2. Install the end of the motion drive belt around the
drivepulley.
3. Make sure the motion drive belt is inside of the belt
guidesnext to the drive pulley. Tighten the belt guides.
4. Put the belt around the idler pulley. Assemble the idler
pulley. Fasten the idler pulley with the hex nut. Make
sure the "V" side of the belt is against the idler pulley.
Also, make sure the belt is not twisted.
5. Check the routing of the motion drive belt. Make sure
the motion drive belt is installed correctly on the idler
pulley. Make sure the motion drive belt is inside all the
belt guides.
6. Before you use the unit, check the adjustment of the
clutch. See the instructions "How To Check And
Adjust The Clutch".
7. Install the mower housing. See the instructions "How
To Install The Mower Housing".

How to replace the mower drive belt

1. Remove the mower housing. See the instructions on
"How to Remove the mower housing".
2. Pull the belt retainer away from the idler pulley and
remove the mower drive belt (Illustration 25).
3. Pull the brake pad away from the jackshaft pulley and
remove the mower drive belt.
NOTE: Replace the mower drive belt with an original
equipment belt from an authorized service center.
4. Install the new mower drive belt. Pull the brake pad
away from the jackshaft pulley. Put the mower drive
belt around the jackshaft pulley.
5. Pull the belt retainer away from the idler pulley. Put
the mower drive belt around the idler pulley.
6. Make sure the "V" side of the mower drive belt is
against the jackshaft pulley and the idler pulley.
7. Install the mower housing. See the instructions on
"How To Install The Mower Housing".
8. Before you mow, check the blade rotation control.
See the instructions on "How To Adjust The Blade
Rotation Control".

How to install the wheels

If the wheels must be removed for service, make sure they
are installed as follows.
Front Wheel
1. Make sure the valve stem is to the outside of the
tractor. Slide the front wheel on the spindle
(Illustration 23).
2. Fasten the front wheel with washer and cotter pin.
Bend the ends of the cotter pin apart to keep the front
wheel on the spindle.
3. If your model has hub caps, install the hub caps.
Make sure the washer hold the hub caps in place.
Rear Wheel
1. Install the washers and spacer onto the axle as
shown in Illustration 24).
2. Mount the square key in the key slot (See Illustration
24).
3. Make sure the valve stem is to the outside of the
tractor. Align the slot in the rear wheel with the square
key. Slide the rear wheel on the axle.
4. Fasten the rear wheel with washer and e-ring.
5. If your model has hub caps, install the hub caps.
Make sure the washer hold the hub caps in place.

How to replace the fuse

If the fuse is blown, the engine will not start. The location
of the fuse is next to the battery. Remove the fuse and
replace with an automotive fuse (Illustration 29).

How to clean the mower housing

WARNING:
Before you clean the mower housing,
stop the engine and disconnect the wire to the sparkplug.
Grass and other debris on top of the mower housing can
keep the belt from working correctly. For safety and
correct operation, frequently clean the top of the mower
housing. Remove grass and debris from around the
pulleys and other moving parts.
1. Move the lever for the blade rotation control to the
ENGAGE position.
2. Clean the top of the mower housing.
3. Move the lever for the blade rotation control to the
DISENGAGE position.
4. Again clean the top of the mower housing.
5. After you cut the grass, clean the bottom of the
mower housing.

Storage and maintenance

Maintain your rider: Check all bolts, screws, nuts and
deck. Dismount the blade and the belt plastic cover for
regular cleaning. Always make sure that the blade is
sharp. It's a good idea to take your lawn rider to an annual
service check with your authorized service dealer. See
your nearest service center at www.texas.dk.
Storage: After use the rider kept in a dry and clean room.
Clean the machine after every use. Grass and dirt must be
removed from the underside of the deck. By tipping the
rider (for cleaning) is recommended to tilt the front up
(max. 45 degrees). If you tilt it sideways, the carburetor
and air filter always face upwards, since oil may run out
32