Fein GIS150 Betriebsanleitung Seite 11

Operating instructions
Switching ON:
➤ Release the safety pushbutton (12) and lift it up.
Press the "I" button (16).
Switching OFF:
➤ Lift up the safety pushbutton (12). Press the "0" (16)
button.
After switching off, the machine runs on for
approx. 50 seconds.
Safety pushbutton:
➤ In emergency situations, press the red safety push-
button to switch the machine off.
Overload protection.
In case of continuous high load over a longer period of
time, the machine is switched off. After a cooling-down
period of approx. 15 minutes, the machine is ready for
operation again.
Contact grinding (Figures 3+4).
➤ Check if the star-knob bolt (9) is firmly tightened.
➤ Ensure that the top protective cover (1) is secured
with star-knob bolt (2) and that the side cover (21)
is shut.
➤ Check the gap size of the grinding rest.
➤ Check the position of the face-grinding rest (18).
The adjustment screws (10) must be in the bottom
position.
➤ Check if the spark guard (4) is properly adjusted and
tightened.
➤ Switch the machine on and check the belt run.
➤ Place the workpiece firmly onto the grinding rest.
➤ Guide the workpiece with both hands or fasten it in
a fixture.
Face grinding (Figure 5).
➤ Loosen star-knob bolt (2) and open the top protec-
tive cover (1).
➤ Make sure that the gap size is correctly adjusted. (Fig-
ure 2)
➤ Switch the machine on and check the belt run.
➤ Guide the workpiece with both hands and remove it
to upward after the working procedure.
Extraction device
➤ The machine can be connected via sleeve (22) to an
exhauster.
Repair and customer service.
Repairs may be carried out only by qualified per-
sons in conformity with the valid regulations.
For repairs, we recommend our FEIN customer service
centre, the FEIN authorised service centres and FEIN
agencies.
Carry out the following maintenance regularly:
Blow out the ventilation slots (15) at the motor
housing and the marked locations with com-
pressed air (see Instruction label (23)).
Lubricate the machine daily (when in use) with
machine oil at the locations marked (see Instruc-
tion label (23)).
➤ Check the drive wheel and the contact wheel for
wear and damage each time when changing the
grinding belt. Have damaged parts replaced.
Warranty and liability.
The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer's guarantee. For further
details on this, please contact your specialist dealer, your
national FEIN representative, or the FEIN customer serv-
ice centre.
Declaration of conformity.
GRIT declares itself solely responsible for this product
conforming with the relevant provisions given on the last
page of this Instruction Manual.
Original language English/German
Environmental protection, disposal.
Stationary machines should be sorted for environment-
friendly recycling in accordance with national laws.
Noise emission values.
A-weighted emission pres-
sure power level measured
at the workplace L
pA
(re 20 µPa), in decibels
Measuring uncertainty K
in decibels
Measured A-weighted sound
power level L (re 1 pW),
wA
in decibels
Measuring uncertainty K
in decibels
Operating conditions
Speed [rpm]
Material
Dimension
Grinding belt
REMARK: The sum of the measured emission value and
respective measuring inaccuracy represents the upper
limit of the values that can occur during measuring.
Wear ear protection!
Measured values determined in accordance with the cor-
responding product standard (see last page in this
Instruction Manual).
en
Idle Sanding
80.5
,
pA
4
90
,
wA
2.5
3000
–
–
–
FEIN 36R
11
94
4
100.5
2.5
3000
ST 37
8 x 40
Grit by