Jacuzzi sasha mi Vorinstallationsblatt Seite 8

Hydraulic connections
For connection to the water supply (position 5) we advise us-
ing pipes with min Ø 14 mm; these pipes must have a 1/2" M
pipe joint.
A tank (optional) may be installed for automatic filling of the
bio sauna/ Roman sauna container; this tank must be connected
to the water supply (cold water) with an 1/2" M fitting (pos. 5S).
In order to ensure correct operation, the pressure and flow
rate values must also comply with the values specified in the rel-
evant "Hydraulic specifications".
Where "hard" water is present, it is advisable to install
a decalcifier in the water system supplying water to the
appliance, in order to reduce and/or avoid calcareous
deposits.
ATTENTION: (IEC 60335-1/A2) The pressure of the wa-
ter system supplying water to the appliance must not
exceed 600 k Pa (6 bar).
Electrical connections
Sasha Mi comes with a multi-pole switch, supplied with a 500 cm.
cable connected to the equipment electrical box, as indicated in pos.
2S, to which the power main is connected.
This switch must be connected to an area that complies with the
safety regulations as specified by current legislation in force.
The electrical connection can be made as follows:
- single-phase line (220-240V 1~)
- three-phase line consisting of three phase conductors +
neutral conductor (380-415V 3N~)
The rated power supply voltage of the equipment is al-
ways 220-240V.
The equipment can also be installed in Countries where
the 220-240V voltage is supplied by a two-phase system. For
the connection please refer to the instruction manual.
Some models allow you to connect the appliance to an alarm
circuit (provided, in the area marked with the bell symbol), a
bipolar cable with characteristics not inferior to type H 05 VV-F
2
2x2.5 mm (220-240V - 2A max.); this cable must be used in order
to ensure that the cable clamp attached to the box offers ad-
equate protection (water tight) as detailed by legislation.
Audio system
The Sasha Mi audio speakers can be connected to a cable audio
system: this must be done by laying out a cable as indicated n
pos. 3.
Upon request, an audio kit is available, which can be installed in
the appliance's appropriate equipment zone, to which the speak-
ers will also be connected.
sauna
10W-8Ω 10W-8Ω
Remote control system arrangement (where present)
The "sauna" and "hammam" functions can be controlled
through a computer which interfaces with a remote system (sc)
via an Ethernet (LAN) network:
sc
it is also possible yo use a smartphone or tablet computer,
which interfaces via a wireless network (WLAN/Wi-Fi):
sc
sim
In any case, you must use an Ethernet socket (RJ-45), as indicated
in position 8, to which the cable (length: ~ 5 m) coming from the
remote control system, must be connected.
The remote control system (to install in the equipment box)
makes it possible to control a maximum number of 5 Sasha Mi.
The cable connecting one Sasha Mi to another must not be
longer than 500 metres (in this is not the case, you may need to
install another remote control system, in order to reduce the length
of the cable section).
Thanks to a SIM card, the Sasha remote control system sends,
via short SMS messages, warnings with regards malfunctions to
a specified mobile telephone; the card (not supplied) must be in-
serted to the remote control system during installation.
We advise you check the cover offered by your mobile tel-
ephone operator.
With regards the management and configuration of the connection
network (LAN, WLAN, Wi-Fi, etc..), we recommend that you consult
a technical expert in the subject.
8
hammam/shower
10W-8Ω 10W-8Ω
LAN
SMS
wi-fi