Bxi1000D / Bxi2000D / Bxi3000D / Bxi4000D; Features And Operational Controls - Hifonics Brutus B3 series Bedienungsanleitung

BXi1000D · BXi2000D · BXi3000D · BXi4000D
BXi 4000D
1x 2000 Watts
1 2
The LINE INPUT RCA jacks must be connected with the RCA output jacks of the headunit.
1
The optional BALANCED INPUT is unlike the regular RCA-cables insusceptible against interspersion and interferences of the
2
vehicle's electronics. You need therefor a Balanced-Line-Transmitter with a special cable, which can be connected between the
head unit and the amplifier. The Balance-Line-Transmitter is not included in delivery. Attend therefor the further information
on page 27. Never use the Balanced-Input and the RCA-Inputs at the same time.
The LEVEL controller adjusts the input sensitivity of the amplifier to align the audio signal from the head unit.
3
The input sensitivity is adjustable from 6 to 0.2 Volts.
The PHASE controller allows to adjust the phasing between 0° and 180°. Thereby you are able to adjust the subwoofer
4
perfect to the vehicle's acustics.
The EXTENDED BASS CONTROL controllers allow a extensive adjustment of the bass frequencies.
5
The SUB BOOST controller defines the bass bosst from 0 to 18dB.
With the FREQ RANGE controller you are able to adjust, on which frequency the bass boost (SUB BOOST) is effictive.
The range goes from 20 to 80 Hz.
With the Q CONTROL controller defines the Q-Factor of the crossover continuously, so that the playback quality of the cut-off
frequency can be adjusted. Thereby you are able to adjust perfect transitions between the loudspeakers.
• WIDE equates a Q-Factor of Q 0,3 (arrow left below) = very wide frequency range.
• NARROW equates a Q-Factor of Q 1,0 (arrow right below) = very narrow frequency range.
• Q 0,5 / LINKWITZ-REILLY is the standard-setting, this means the arrow points up (12 o'clock position).
The SUB SONIC controller (Subsonicfilter) limits the ultralow and not hearable frequencies of the audiosignal to below, to avoid
6
a mechanical and electical overloading on the subwoofer. The cut-off frequency is adjustable from 15 to 55 Hz and depends on
the size of the subwoofer.
The MODE switch selects the required operation mode of the amplifier.
7
In the SLAVE-Mode the amplifier works as a SLAVE amp, this means only the audiosignal of the MASTER amp will be amplified.
All controllers on the SLAVE Amp are without function and will be assumed by the MASTER amp.
In the MASTER-Mode (Low Pass mode) you are able to limit the frequencies to above with the LOW PASS controller. All controllers
are active. NOTE: By using only one amplifier, the Mode-Switch must set to the position MASTER.
The LOW PASS controller adjusts the cut-off point of the frequency range to above. The cut-off frequency is
8
continuously adjustable from 35 Hz to 250 Hz.
The REMOTE port is for the cable of the enclosed bass remote controller and only to use in the MASTER mode. With this bass
9
remote controller, you are able to adjust the bass level e.g. out of the driver's seat. Please use only the enclosed bass remote
controller and cable.
POWER/PROTECT
10
If the POWER LED lights up, the amplifier is ready for operation.
If the PROTECT LED lights up, a malfunction is indicated. Attend in this case the chapter TROUBLE SHOOTING.
The SLAVE IN/OUT RCA jacks are suitable to connect an additional amplifier in MASTER/SLAVE mode.
11
Attend therefor the chapter Interconnection Example: MASTER/SLAVE on page 21.
FUNCTIONS AND OPERATIONAL CONTROLS
3 4 5
SLAVE IN/OUT
SLAVE MASTER
MODE
6 7 8 9
19
10 11