Schüco 1600 Pro Anleitung Seite 30

The Transfer system is protected against overload
with a 16Amp. automatic safety fuse on the AC Input
side of the Inverter 1600 Pro. If the system has been
overloaded the button/pin of the fuse will pop-out. To put
the automatic safety system back in to operating you
must push this pin back.
In the Inverter operation, the Inverter 1600
Pro generates a true sinusoidal and quartz
stabilized output voltage.
When, however the Inverter 1600 Pro is
supplied from a grid or a generator and the
transfer contact is active, then you have at
the output AC OUT the same voltage as
that at the input.
This voltage can not be modifi ed by the
Inverter 1600 Pro!
4.3.1 Set the transfer voltage threshold
The voltage threshold of the transfer is factory settled
at 200Vac. This value is acceptable in most application.
However, this value can be adjusted from 150 to 230Vac
if necessary. To pro-ceed to the adjustment of this level,
insert slowly a screw-driver "imbus" 2mm in the hole
and turn gently clockwise or counter clockwise to
increase or diminish the threshold level.. When the
Input voltages reach the settled value on turning knob,
the inverter switch off and the AC INPUT go directly on
the AC OUTPUT. When the voltage INPUT is less of
20V the value set, the transfer is stop and the OUTPUT
switch back on the inverter.
4.3.2 FAST (UPS)- MODE for the Transfer
Switch
The quick and break free Transfer mode is programmed
with a slide switch „Transfer Delay" OFF
the front side (cable connections side).
The aim of the Inverter 1600 Pro is to supply the
consuming appliance with a break-free alter-nating
voltage. When the incoming voltage AC IN no longer
matches values, the Inverter switches on at once.
The transfer is carried out in 0.02 seconds. This
quick transfer ensures a break-free function for most
consuming appliances. If you have an alternating
voltage a correct value back at the input AC IN, transfer
system starts up again without any break, and the in-
verter is stopped.
The delayed mode of the transfer system „Transfer
Delay ON" is programmed with the slide switch on
front with the cable connections. The Inverter 1600
Pro provides a break-free alternating voltage for the
consuming appliance. A quick transfer switch is not
always sensible nor is it always desired. For example,
when the consuming appliances are operated by a small
back-up generator, an overload of a short duration on
such a generator, i.e. start of a vacuum cleaner etc.,
has the effect of decreasing the voltage for a short
time. As in such cases the transfer to the Inverter is not
32
desirable, the transfer system can be programmed with
a delay. When the slide switch (Transfer delay) is in the
„On" position, the transfer to the inverter takes place
with a delay of 5 seconds. If the voltage falls below
100Vac, the transfer takes place without delay! The
transfer switching to the Inverter takes place without any
break.
4.3.3 Delayed mode of the Transfer System
The delayed mode of the transfer system „Transfer
Delay ON" is programmed with the slide switch on front
with the cable connections. The Inverter Pro provides
a break-free alternating voltage for the appliance. A
quick transfer switch is not always sensitive nor is it
always desired. For example, when the appliances are
operated by a small back-up generator. An overload of a
short period on such a generator, i.e. start of a vacuum
cleaner etc., has the effect of decreasing the voltage for
a short time. As in such cases the transfer to the Inverter
is not desired, the transfer system can be programmed
with a delay. When the slide switch (Transfer delay) is in
the „On" position, the transfer to the inverter takes place
with a delay of 5 seconds. If the voltage falls below
100Vac, the transfer takes place without delay ! The
transfer switching to the Inverter takes place without any
break.
4.4
Operating voltage of lead-acid batteries change depends
on the temperature. To correct the operating voltages
according to the actual temperatures, a temperature
sensor can be con-nected to the Inverter 1600 Pro.
The compensation through the sensor is –3mV/°C/Cell.
, which is on
Order Number for
TS Pro: 231 643
Dimensions:
58 x 51.5 x 22 mm
231 575
The Temperature sensor TS Pro
02.2008