ENGLISH
8
Adjusting functions
Use the ¡ and ™ buttons to switch from function to function (fig. 18).
1
The blinking symbol indicates which function is being adjusted.
2
Options:
Select • to set the time.
-
Select ª to set the facial tanner.
-
-
Select ≠ to set the body cooler.
Setting the time for a tanning session
Select • to set the time.
1
Press the ¢ button to put the time forward and push the £ button to put the time backward (fig. 19).
2
Keep the button pressed in to adjust the time more quickly.
Setting the facial tanner
Select ª to set the facial tanner.
1
Press the ¢ and £ buttons to set the intensity of the facial tanner (fig. 20).
2
-
O = off
-
1 = 50% of its full intensity
-
2 = full intensity
◗
If you have not set the intensity within approx. 5 seconds, the set tanning time will be shown on the display again.To set the facial tanner,
select ª.
◗
If you do not set the facial tanner, the facial tanner will burn at full intensity.
Setting the body cooler
Select ≠ to set the body cooler.
1
Press the ¢ and £ buttons to set the fan power of the body cooler (fig. 21).
2
-
O = no body cooling
-
1 = body cooler fan at minimum setting
-
2 = body cooler fan at moderate setting
-
3 = body cooler fan at high setting
-
4 = body cooler fan at maximum setting
◗
If you have not set the fan power within approx. 5 seconds, the set tanning time will be shown on the display again.To set the body
cooler, select ≠.
◗
If you do not set the body cooler, the body cooler fan will work at maximum setting.
Tanning
1
Put on the protective goggles provided.
3
Switch the tanning lamps on by pressing the green I button.
◗
The display shows the remaining tanning time.
◗
During the tanning session, the dot next to the time indication blinks.
◗
If you want to switch the appliance off during the tanning session, press the red O button.
A few seconds after the appliance has been switched off, the cooling fans go on automatically to cool down the appliance for 3 minutes (if the
B
standard setting has not been changed). Symbol – and the remaining cooling time (180-0 seconds) are shown on the display.
◗
You can adjust the intensity of the facial tanner during the tanning session. Use the ¡ and ™ buttons to select ª and then set the
required intensity.The new setting becomes active immediately.
If you have not set the intensity within approx. 5 seconds, the remaining tanning time will be shown on the display again.
B
B
If you want to set the facial tanner from O (off position) to 1 or 2 while the lamps have not yet cooled down sufficiently, the O symbol will blink on
the display.
◗
You can adjust the fan power of the body cooler during the tanning session. Use the ¡ and ™ buttons to select ≠ and then set the
required power.The new setting becomes active imediately.
B
If you have not set the fan power within approx. 5 seconds, the remaining tanning time will be shown on the display again.
◗
During the last 5 seconds of the tanning session,you will hear a beeping sound and the appliance will switch off automatically after these
5 seonds.
B
A few seconds after the appliance has been switched off, the cooling fans go on automatically to cool down the appliance for 3 minutes (if the
standard setting has not been changed). Symbol – and the remaining cooling time (180-0 seconds) are shown on the display.
Adjusting the appliance
Owner's instructions for adjusting the appliance
This part of the manual contains information about additional adjustment options for the owner.
B
Setting the additional options
Freezing the set time
Select • to set the time.
1
Press the ¢ button to put the time forward and push the £ button to put the time backward.
B
Keep the button pressed in to adjust the time more quickly.
B
2
Hold down the red O button while pressing the ¢ button, the £ button and the ¢ button in succession.Then release the O button.The
set time is now frozen.
The set time can no longer be adjusted.
B
◗
Symbol • stops blinking.