Noise Information - AEG BPS18-254BL Originalbetriebsanleitung

Technical Data
Mitresaw *
Production code
Battery voltage
No-load speed
Saw blade dia. x hole dia
Saw blade body thickness max.
Saw blade tooth thickness min.
Recommended Ambient Operating Temperature
Recommended battery types
Recommended charger
Max. cutting capacity
Mitre 0°/ Bevel 0°
Mitre 0°/ Bevel 45°
Mitre 0°/ Bevel 45°
Mitre 45°/ Bevel 0°
Mitre 45°/ Bevel 0°
Mitre 45°/ Bevel 45°
Mitre 45°/ Bevel 45°
Weight according EPTA-Procedure 01/2014 (Li-Ion 5,0 Ah)

Noise information

Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
PS Mitresaw
*
^
=
WARNING
The declared noise emission value(s) have been measured in accordance with a standard test method of EN 62841-1 and EN 62841-3-9,
and may be used for comparing one tool with another. The declared noise emission value(s) may also be used in a preliminary assessment
of exposure.
The noise emissions during actual use of the power tool can di er from the declared values depending on the ways in which the tool is
used especially what kind of workpiece is processed.
Identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as the times when the tool is switched o and when it is running idle in addition to the
trigger time).
Wear ear protectors. Exposure to noise can cause hearing loss.
WARNING Read all safety warnings, instructions,
illustrations and speci cations provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS FOR MITRE SAWS
a) Mitre saws are intended to cut wood or wood-like
products, they cannot be used with abrasive cut-o wheels
for cutting ferrous material such as bars, rods, studs, etc.
Abrasive dust causes moving parts such as the lower guard to jam.
Sparks from abrasive cutting will burn the lower guard, the kerf
insert and other plastic parts.
b) Use clamps to support the workpiece whenever possible.
If supporting the workpiece by hand, you must always
keep your hand at least 100 mm from either side of the saw
blade. Do not use this saw to cut pieces that are too small
to be securely clamped or held by hand. If your hand is placed
too close to the saw blade, there is an increased risk of injury from
blade contact.
c) The workpiece must be stationary and clamped or held
against both the fence and the table. Do not feed the
workpiece into the blade or cut "freehand" in any way.
Unrestrained or moving workpieces could be thrown at high
speeds, causing injury.
d) Push the saw through the workpiece. Do not pull the
saw through the workpiece. To make a cut, raise the saw
head and pull it out over the workpiece without cutting,
start the motor, press the saw head down and push the saw
through the workpiece. Cutting on the pull stroke is likely to
cause the saw blade to climb on top of the workpiece and violently
throw the blade assembly towards the operator.
e) Never cross your hand over the intended line of cutting
either in front or behind the saw blade. Supporting the
workpiece "cross handed" i.e. holding the workpiece to the right of
the saw blade with your left hand or vice versa is very dangerous.
f) Do not reach behind the fence with either hand closer
than 100 mm from either side of the saw blade, to remove
wood scraps, or for any other reason while the blade is
spinning. The proximity of the spinning saw blade to your hand
may not be obvious and you may be seriously injured.
BPS18-254BL
4740 20 01...
...000001 - 999999
18 V
3900 min
-1
254 x 30 mm
1,6 mm
2,2 mm
-18°C ... +50°C
L18...
AL1218... / BL 1218...
90 mm × 305 mm
39 mm × 305 mm
43 mm × 305 mm
90 mm × 215 mm
50 mm × 215 mm
39 mm × 215 mm
43 mm × 215 mm
16,3 kg
89,0 dB (A)
98,5 dB (A)
English
29
GB