Seav LRX 2215 Bedienungsanleitung Seite 8

P B I
ROGRAMMING UTTONS AND NDICATOR
SEL button: selects the type of function to store in the memory; selection is indicated
by the LED flashing. The desired function can be selected by pressing the button
repeatedly. The selected function remains active for 15 seconds (flashing LED), after
which the control unit returns to its original status.
SET button: programmes the function that has been selected using the SEL. button.
Indicator LEDs
LED lit: option stored.
LED off: option not stored.
LED flashing: option selected.
MAIN MENU
Reference LED LED Off
1) CODE No code
2) SENS. CODE No code
3) T. MOT Motor running time 2 minutes Motor running time pgm.
4) WIND SPEED Wind safety 25 km/h
A) CODE (Radio control programming)
Programming using a 1- or 2-button radio control:
To programme the transmission codes in the radio control, proceed as follows: press
the SEL button; the CODE LED begins to flash. Send the first preselected code using
the relevant radio control at the same time; the CODE LED begins to flash rapidly. Send
the second code to be stored: the CODE LED will remain lit and programming will be
complete. If the second code is not sent within 10 seconds the control unit exits the
programming stage, selecting operation using a single button on the radio control.
Programming using a 3-button radio control in the "BeFree" series:
The control unit allows you to store the whole "BeFree" radio-control by programming
only the Up button.
To programme the "BeFree" radio control codes, follow this procedure: press the SEL
button; the CODE LED begins to flash. Press the Up button on the desired radio con-
trol at the same time; the CODE LED will remain lit and programming will be complete.
Deleting the codes: To delete all transmission codes stored in the memory, proceed
as follows: press the SEL button; the CODE LED will start to flash. Then press the SET
button; the CODE LED will switch off and the procedure is complete.
Radio control already stored warning:
If the user attempts to perform the programming procedure for a radio control which is
already stored in the memory, the CODE LED will begin to flash rapidly for a few
moments, to indicate that this procedure cannot be performed; the unit then returns to
the programming stage once again.
Maximum number of radio controls which can be stored:
If the maximum number of radio controls has been reached and a programming pro-
cess started, the control unit will indicate that it has failed by flashing all the LEDs
except the CODE LED, which will remain lit in a constant manner. After 10 seconds the
control unit exits programming mode.
L
EDS
LED On
TX Pgm code
Sensor code pgm.
Wind safety pgm.
B) SENS. CODE (Wireless Sensor programming)
Wireless Wind sensor programming:
To programme the Wireless Wind Sensor transmission code, proceed as follows: Use
the SEL button to navigate to a position where the SENS. CODE LED flashes; at the
same time, send the Wireless Wind sensor code using the special button inside the
sensor. The SENS. CODE LED will remain lit in a fixed manner and programming will be
complete. If the Wireless Wind sensor code is not sent within 2 minutes, the control unit
exits programming mode.
Deleting the codes:
To delete the Wireless Wind sensor codes stored in the memory, proceed as follows:
press the SEL button; the SENS. CODE LED will start to flash. Then press the SET but-
ton; the SENS. CODE LED will switch off and the procedure is complete.
Wireless Wind sensor already stored warning:
If the user attempts to perform the programming procedure for a Wireless Wind sensor
which is already stored in the memory, the SENS. CODE LED will begin to flash rapid-
ly for a few moments, to indicate that this procedure cannot be performed; the unit then
returns to the programming stage once again.
Maximum number of Wireless Wind sensors which can be stored:
If the maximum number of Wireless Wind sensors has been reached and a program-
ming process started, the control unit will indicate that it has failed by flashing all the
LEDs except the SENS. CODE LED, which will remain lit in a constant manner. After 10
seconds the control unit exits programming mode.
Warning indicator:
If there is no communication between the Wireless Wind sensor and the control unit,
after 20 minutes the safety upward movement will be activated automatically. If this
lack of communication persists, further commands will still, nevertheless, result in the
control unit being set to safety mode.
C) T. MOT. (Max. Motor Timer programming time 4 minutes)
The control unit comes with a motor power supply time of two minutes (T. MOT. LED
OFF).
The motor running time must be programmed when the shutter is down, in the follow-
ing manner:
Press the SEL button until the T. MOT LED flashes, then press and hold the SET but-
ton; the shutter will begin to move upwards. Once the desired position has been
reached, release the SET button – at this very moment, the motor running time will be
stored and the T. MOT LED will remain lit.
If you are using an automation which has a stop limit, we recommend that you set a
time which exceeds the stop limit of the shutter by a few seconds.
If you want unlimited motor running time, perform the same programming procedure,
holding down the SET button for less than two seconds; the T. MOT LED will remain lit
and the unlimited time function will be set. The procedure may be repeated if a mistake
is made during programming.
- 8 -