Installation - Vimar Elvox Petrarca series Installations- Und Benutzerhandbuch

Controls
The call volume can be adjusted by moving the loudspeaker wire from con-
nector A+ (high) to A- (low); otherwise use accessory type 6153/682, leaving
the loudspeaker wire connected to connector A-.

INSTALLATION

Wall-mounted installations of the interphone do not require additional acces-
sories. However a vertical 3-module box may be used to facilitate fixture and
cable routing. For desktop installations and combinations with monitors, refer
to the respective instructions of the conversion kit or monitor.
Bus termination for video signal stabilisa-
tion
The interphone is provided with a "BUS ter-
mination connector" (A-B-C) for video signal
stabilisation.
Depending on the connection configuration
(interphones/monitors connected in series or
derived from a distributor), set a jumper on the
connector ABC as described in the note "Bus
termination for ELVOX TWO-WIRE INSTALLA-
TIONS" in the wiring diagrams section below.
A
C B
GB
PROGRAMMING
There are three interphone programming modes: assignment of an identifica-
tion code or call code (indispensable), assignment of a secondary identifica-
tion code (for interphones associated with a master interphone), programming
of pushbuttons for auxiliary services and intercommunicating calls (when ne-
cessary).
Programming must be performed with the system switched on, without active
communication and only after connecting the interphones/monitors to the sy-
stem and programming the panels.
Identification code programming
The identification code is programmed via an entrance panel (MASTER), al-
ready configured and present on the system. The interphone is supplied wi-
thout associated identification code. To verify this condition, press the lock
release pushbutton and the interphone should emit a triple "Beep".
Attention: during the interphone/video interphone identification code pro-
B
gramming you have 30 seconds from the moment you enter the pro-
gramming in the interphone/video interphone and the moment you press
the call push-button on the panel or you send the code.
Programming phase:
1) Remove the interphone cover.
2) Press and hold the RESET pushbutton on the interphone.
3) Press and hold the tab on the lock release pushbutton, together with the
A
RESET pushbutton.
4) Release the RESET pushbutton, keeping the lock release pushbutton
pressed.
5) After 2 seconds the interphone emits a high tone and communication is
enabled with the panel. If the monitor is also connected to the interphone,
it is switched on and connected to the camera of the entrance panel.
6) Release the tab of the lock release pushbutton.
A
7) On pushbutton entrance panels, press the call button for the interphone,
while on alphanumeric keypads, enter the call code and press pushbut-
ton "
8) If the system contains an interphone that already has the same associa-
ted identification code, the panel emits a low signal and the operation
should be repeated from point 2.
A
9) Otherwise the code is associated with the interphone and communication
is terminated.
Secondary identification code programming
Programming of the secondary identification code is only required when more
than one interphone is to be called by means of the same pushbutton or call
code. The interphones that ring at the same time are associated with the same
group. The "master" interphone is programmed first by means of the "identi-
fication code programming" procedure described above, while the additional
group interphones are programmed with the secondary identification code
(see table shown in the wiring diagram section).
Fig. 2
A maximum of three audio door entry units plus one group master can be
associated with the same group, without the need for programmer Type
950C or SaveProg .
If the interphones are combined with Petrarca monitors, an additional
power supply type 6923 must be fitted for each additional monitor after
the second monitor. Using programmer type 950C, activation of the rin-
gtone on all monitors can be programmed, without simultaneous activa-
tion of all monitors, to then enable activation of the monitor from the
interphone used to answer the call with the self-start pushbutton; this
avoids the need to use additional power supplies.
Programming phase:
Fig. 3
1) Remove the interphone cover.
2) Press and hold the RESET pushbutton on the interphone.
3) Press and hold the tab on the lock release pushbutton and the self
start/auto-activation pushbutton (the first pushbutton below the tab), to-
gether with the RESET pushbutton.
4) Release the RESET pushbutton, keeping the other two pushbuttons
pressed.
5) After 2 seconds the interphone emits a high tone and communication is
enabled with the panel. If the monitor is also connected to the inter-
phone, it is switched on and connected to the camera of the entrance
panel.
6) Release the tab on the lock release pushbutton and the self start pu-
shbutton.
".
5