swissflex _75RF bridge Bedienungsanleitung Seite 26

Initial setup «Classic»
Place the batteries into the radio remote control
Remove the cover from the battery compartment (8)
on the back of the radio remote control. Place 3 AAA-
batteries (9) into the compartment, paying attention to
the +/- markings. Close the compartment cover again.
The maximum range of the radio remote control is 15
metres.
Teaching-in the radio remote control (already
taught-in in the factory)
1. Remove the radio remote control's battery cover on
the back of the device.
2. Insert / check the batteries (3 x AAA).
3. Activate the teach-in button (17) on the switching
power supply (press 2 x). Now the motor's emer-
gency light turns on.
4. Press buttons (1+2) simultaneously on the radio
remote control until the motor's emergency light
turns off. This means that pairing has been com-
pleted.
Synchro function (with sync cable)
When two _75RF / _75RF bridge® are linked together
with a sync cable (connection jack (10)), the synchro
function is required. By pressing and holding down
the button (6+7), the synchro function is activated/
deactivated. When pressing the travel button (1-4),
the control systems synchronise and then move in the
confirmed direction of travel. After plugging in the sync
cable, carry out a reset as follows:
Press button (17) on the switching power supply (15)
until all of the motors have powered down and this
is confirmed by the motor's emergency light blinking
twice (can take 20 seconds).
The internal meter readings for the individual motors
have now been reset to '0' and the sync function can
work correctly.
Under-floor lighting
Activate the under-floor lighting by pushing the
„Under-floor lighting" buttons (1+2). This switches
off automatically after 30 minutes, or if the button is
pushed once again.
Pocket lamp
The pocket lamp is illuminated when the „Pocket
lamp" button (7) is held down. The light turns off when
the button is released.
26
Operating instructions
Adjustment options «Classic»
You can individually adjust the back section or the thigh
section by using the buttons (1-4).
All motors can be simultaneously put in position «up»
or «down» with the buttons (5) and (6).
To reset to the horizontal position
Press the "all motors down" button (6) to simultane-
ously move all sections to the horizontal position.
Care and Maintenance
«Classic»
Your _75RF / _75RF bridge® is a high-quality product
that has been designed to serve you reliably for many
years to come. For occasional cleaning and the remo-
val of dust, we recommend the use of a dry cloth.
Changing the batteries in the radio remote control
Remove the cover from the battery compartment (8) on
the back of the radio remote control. Place three AAA
batteries into the compartment, paying attention to the
+/- markings. Close the compartment cover again.
Changing the batteries in the uni 14_/15_/22_/20
_75RF / _75RF bridge®RF / _75RF / _75RF
bridge®RF bridge® switching power supply (15)
(batteries for emergency lowering)
Carefully remove the batteries from the battery clips.
Place two 9V block batteries in the compartment, pay-
ing attention to the +/- markings. The batteries in the
switching power supply provide power in the case of a
power failure.
Troubleshooting «Classic»
In case of malfunctions with your uni 14_/15_/22_/20
_75RF / _75RF bridge®RF / _75RF / _75RF bridge®RF
bridge®, consult the following troubleshooting tips. If
the problem cannot be resolved, disconnect the _75RF
/ _75RF bridge® from the mains outlet and contact
your Swissflex stockist.
Loss of power in the sitting position; emergency
lowering button
The switching power supply (15) contains two bloc
batteries to revert the bed to the horizontal (sleeping)
position in the event of a power failure while sitting up
in the bed:
Hold the emergency lowering button (17) down until all
sleeping surfaces are in the horizontal position. Once
voltage has been restored, wait at least 10 seconds be-
EN