swissflex _75RF bridge Bedienungsanleitung Seite 23

The internal meter readings for the individual motors
have now been reset to '0' and the sync function can
work correctly.
Under-floor lighting
Activate the under-floor lighting by pushing the
„Under-floor lighting" button (8). This switches off
automatically after 30 minutes, or if the button is
pushed once again. This button is illuminated (blue)
when it is pushed.
Pocket lamp
The pocket lamp is illuminated when the „Pocket
lamp" button (5) is held down. The light turns off
when the button is released. This button is illumi-
nated (blue) while the pocket lamp is in use.
Lock buttons
To lock the buttons, hold down the „Lock buttons"
button (16) for five seconds. Once the button lock has
been activated, all buttons (except for the mains out-
let (15), the pocket lamp (5), the under-floor lighting
(8) and the button lock (16)) flash (blue) twice.
All buttons flash twice (white) when a disabled button
is pushed. The lock is disabled by holding down the
„Lock buttons" button (16) for five seconds. All but-
tons flash twice (blue) if this was successful.
Adjustment options «Touch»
The sleep and sit positions have been pre-pro-
grammed in the factory.
M1 Read and watch TV without getting tired
M2 Relieving position for colds, respiratory disor-
ders or cardiovascular complaints
M3 Ergonomic position for backaches and inverte-
bral disk complaints
M4 Aids for getting into and out of the bed
The positions can be overwritten individually.
Resetting the factory-programmed memory posi-
tions
Hold down the memory button (14) for 3 seconds –
the background lighting then flashes once, the under-
floor lighting button (8) must then be pressed within
a second. The entire RF-Touch lighting flashes twice
to confirm that the factory settings have been reset.
Saving the sitting and lying position to a memory
button
1. Press the memory button (14) 3 x within 2 seconds.
2. The memory button is illuminated (blue) (1–4).
3. Press the desired memory button for memory po-
sition 1–4 (1–4) 1x within three seconds.
EN
The programming of a new position automatically
overwrites an old position. A successful save is visu-
alised by a change in colour of the selected memory
button LED (white). All memory buttons turn white
two seconds after the memory button is released.
To call up a position stored in memory
Press the desired memory button for memory posi-
tion (1–4), until all the comfort sections have reached
the programmed position. The activated memory but-
ton is illuminated (blue) during the travel time.
To reset to the horizontal position
Press the "all motors down" button (7) to simultane-
ously move all sections to the horizontal position.
Care and Maintenance «Touch»
Your _75RF / _75RF bridge® is a high-quality prod-
uct that has been designed to serve you reliably for
many years to come. For occasional cleaning and the
removal of dust, we recommend the use of a dry cloth.
Changing the batteries in the radio remote control
Remove the cover from the battery compartment (17)
on the back of the radio remote control. Place three
AAA batteries into the compartment, paying attention
to the +/- markings. Close the compartment cover
again.
Changing the batteries (25) in the _75RF / _75RF
bridge® switching power supply (batteries for
emergency lowering)
Carefully remove the batteries from the battery clips.
Place two 9V block batteries in the compartment,
paying attention to the +/- markings. The batteries
in the motor provide power in the case of a power
failure.
Troubleshooting «Touch»
In case of malfunctions with your _75RF / _75RF
bridge®, consult the following troubleshooting tips.
If the problem cannot be resolved, disconnect the
_75RF / _75RF bridge® from the mains outlet and
contact your Swissflex stockist.
Loss of power in the sitting position; emergency
lowering button
The switching power supply contains two bloc batter-
ies (25) to revert the bed to the horizontal (sleeping)
position in the event of a power failure while sitting
up in the bed:
Operating instructions
23