Werbung
ELECTRICAL CONNECTIONS
5. ELECTRICAL CONNECTIONS
5. ELECTRICAL CONNECTIONS
ON
ON
1 2 3
1 2 3
BL
41
8
6
4
3
1
Alimentazione
Power supply
BL
41
8
6
4
3
1
Alimentazione
Power supply
230 V~ 0,2 A
ON
230 V~ 0,2 A
ON
1 2 3
TC
1 2 3
TC
i
-Max section of the wire that can be used on a single clamp = 1.3 mm ² (26AWG).
i
-Max section of the wire that can be used on a single clamp = 1.3 mm ² (26AWG).
-If used wires with a larger diameter or more wires, make an external connection using a special terminal (not supplied).
-If used wires with a larger diameter or more wires, make an external connection using a special terminal (not supplied).
5.1 Commands
5.1 Commands
Command
Funzione
Command
Funzione
The opening manoeuvre starts when the contact is closed.
1
3 N.O. OPENING
The opening manoeuvre starts when the contact is closed.
1
3 N.O. OPENING
The closing manoeuvre starts when the contact is closed.
1
4 N.O. CLOSING
The closing manoeuvre starts when the contact is closed.
1
4 N.O. CLOSING
The coincidence of an opening and closing command stops all movements.
1
3
The coincidence of an opening and closing command stops all movements.
N.O. STOP
WARNING: when the contact opens again the door proceeds with the
1
3
1
4
N.O. STOP
WARNING: when the contact opens again the door proceeds with the
interrupted manoeuvre.
1
4
interrupted manoeuvre.
1
6 N.C. NOT USED
Make a jumper on contact 1-6 if DIP 3 =OFF, make a jumper on contact 41-6 if DIP 3 =ON.
1
6 N.C. NOT USED
Make a jumper on contact 1-6 if DIP 3 =OFF, make a jumper on contact 41-6 if DIP 3 =ON.
CLOSING
The opening of the contact reverses the movement (re-opening) during the closing operation.
1
8 N.C.
CLOSING
SAFETY
NB: If no closing safety device is used and DIP3= ON, a jumper must be made on contacts 41-8.
The opening of the contact reverses the movement (re-opening) during the closing operation.
1
8 N.C.
SAFETY
NB: If no closing safety device is used and DIP3= ON, a jumper must be made on contacts 41-8.
CONTACT
CONTACT
Terminal 41 activates a test of the safety device on each cycle. If the test fails the RED LED flashes briefly and
SAFETY
Terminal 41 activates a test of the safety device on each cycle. If the test fails the RED LED flashes briefly and
41
(+)
the test is repeated. With DIP3=ON connect terminal 41 and 0 of the control panel to the corresponding test
SAFETY
N.C.
DEVICES
41
(+)
the test is repeated. With DIP3=ON connect terminal 41 and 0 of the control panel to the corresponding test
0
(-)
terminals on the safety device.
N.C.
DEVICES
TEST
0
(-)
terminals on the safety device.
If the safety devices are not tested, see description DIP3=OFF.
TEST
If the safety devices are not tested, see description DIP3=OFF.
5.2 Output and accessories
5.2 Output and accessories
Output
Value - Accessories
Output
Value - Accessories
Accessories power supply.
Accessories power supply.
Power supply output for external accessories.
0 1
24 V
0,36 A
Power supply output for external accessories.
0 1
24 V
0,36 A
- +
- +
1 BL
1 BL
+
-
+
-
Blocking device
Blocco
Blocking device
Blocco
Test sicurezze
Safety devices test
Test sicurezze
Safety devices test
Sicurezza in chiusura
Closing safety contact
Sicurezza in chiusura
Closing safety contact
Sicurezza in apertura
Opening safety contact
Sicurezza in apertura
Opening safety contact
Chiusura
Closing
Closing
Chiusura
Opening
Apertura
0
Apertura
Opening
0
+
24 V
+
-
24 V
-
BL
41
8
6
4
3
1
0
BL
41
8
6
4
3
1
0
Descrizione
Descrizione
Description
Description
DO NOT USE
DO NOT USE
5.3 Adjustments
TRIMMER/DIP SWITCHES ADJUSTMENT ENABLING PROCEDURE
The trimmers and DIPs affect the force limiting safety function. They must be set as instructed, (if not, the modifications will not be accepted and
the RED and GREEN LEDs will flash):
• During the setting phase, the operator stops and it is not possible to carry out commands.
• Press the button
for 4 s (RED and GREEN LEDs on);
• Adjust the trimmers and DIP switches within the 5-minute time limit;
• To complete the procedure, press the button for 2 s, the operator continues the previously interrupted operation
DIP1
Closure thrust.
Maintain the door wing in the closure position.
0,36 A
4
3
1
0
0,36 A
DIP2
Direction selection.
ON
The opening direction is intended by viewing the auto-
mation from the side being examined.
1 2 3
DIP3
Safety test terminal 41
TC
Automatic closing time. From 0 to 30 s.
Adjust the time that passes between the end of the opening operation and the start of the automatic closing operation.
The count is reset when an opening command is given with the door open.
0 s
disable
Adjust the TC to the maximum if automatic closing is not required.
DIP "WEIGHT"
ON
1 2 3
LED
Green
Power supply on
Red
Safety contacts 6 or 8 open.
Red + Green
Trimmer/dip switches adjustment
+
procedure enabling
Red + Green
/
Opening:
Press quickly to activate the opening operation
ENABLING of trimmer/dip switches adjustment:
(red+green LEDs on, see enabling procedure)
6. REQUISITES FOR DOORS FOR LOW ENERGY USE
The OLLY C automation is factory supplied with maximum performance setting. If used with the Low Energy service, the "Weight" dip switches must
be selected according to the weight of the door wing, as shown in the following table.
NB: consider the weight of a single door wing.
Attention: an incorrect setting of the dip with respect to the weight of the door leads to an incorrect speed and consequent operation inconsistent
with Low Energy use.
ON
1 2 3
DIP "WEIGHT"
DIP1
DIP2
OFF
OFF
ON
OFF
OFF
ON
ON
ON
OFF
OFF
ON
Description
Disabled.
Righthand opening.
Automation with 2 door wings
Disabled The safety sensors are not monitored and the
NC contacts must be connected to terminals 1-6 and 1-8
Description
Select wing weight for LOW ENERGY use
Acceso
Encoder not working or automation faulty.
Safety test failure.
• 2 flashes = trimmer/dip switches adjustment confirmed
• 4 flashes at 1s intervals, indicates that an adjustment has been made without first ena-
bling the adjustment procedure:perform the enabling procedure again.
Alternately flashing light
the automation is stopped due to coinciding opening and closing commands
DIP3
Weight of a door wing
Opening speed
Up to a max 40 kg (1 door)
0,40 m/s
OFF
or 2 x 27 kg (2 doors)
Up to 25 kg
0,36 m/s
OFF
Refer to the data sheets
From 26 → 30 kg
0,34 m/s
OFF
for more details.
From 31 → 35 kg
0,31 m/s
OFF
From 36 → 40 kg
0,29 m/s
ON
OFF
ON
Enabled
Lefthand
opening
Enabled
OFF
ON
See chapter 6
See chapter 6
Flashing light
Performance
Maximum performance,
NO Low Energy
Low energy
performance
DO NOT USE
Werbung
