Herunterladen Inhalt Inhalt Diese Seite drucken

Jacuzzi sasha Montageanweisung Seite 21

Sauna+shower+hammam
Vorschau ausblenden Andere Handbücher für sasha:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 84
Sasha / Sasha white:
(
cable and bring it near the electronic box, as indicated.
Sasha / Sasha white:
(
it rests against the respective frame. Adjust its position, by lifting it
as much as is needed to move it outwards and close any openings
between frame and roof.
Sasha / Sasha white:
(
head to the hammam's mixing system.
Sasha / Sasha white:
(
ble to the terminal indicated.
Sasha (Sauna / Hammam); Sasha white (Hammam)
(
32) Fix the roof to the walls and apply the cover panels us-
ing soft double-sided tape and heat resistant silicone.
Shower:
(
33, detail 1) Position the roof so that the back of the roof
rests against the wood frame and the roof sides rest against the
adjacent profiles.
(
33, detail 2) After having checked the alignment of the
shower frame with adjacent frames, make holes in these afore-
mentioned frames which align with the holes in the shower
frame.
Then attach this frame to the adjacent frames.
(
33, detail 3) Position the roof so that it is within the in-
ner edge of the respective frame, paying attention to the plastic
edge protectors previously attached with silicone.
(
34, detail 1) Connect the shower heads to the mixing
system using the bend fittings supplied (refer to the indicated
labels, which also feature on the tubes themselves).
(
34, detail 2) Connect the light cable to the respective
junction box.
If the shower has a door, install the fixed glass supports
to the roof and the base frame structure; refer to the
attached documentation.
Installing the shower wall (2)
(
35, detail 1) Draw in the wall and connect the pipe com-
ing from the mixing system to the shower cascade.
(
35, detail 2) Place the wall on top of the one underneath,
ensuring coupling, and attach it to the panel as indicated.
Benches and duckboards
Sauna:
(
36, details 1-2) Position the heater cover and proceed
with the positioning of the duckboards (wood) adjacent to the
side walls.
31, detail 2-3) Unwind the sensor
31, detail 4) Position the roof so that
31, detail 5) Connect the shower
31, detail 6) Connect the sensor ca-
(
36, details 3-4-5) Position the highest bench against the side
wall and connect the light cable underneath the cable coming from
the wall, sealing the cable outlet with the foam rubber bushing.
(details 6-7) Finish positioning the duckboards and then po-
sition the lower bench.
Shower:
(
37) Check that the drain covers are present and then pro-
ceed with the positioning of the duckboard.
Hammam:
(
38 , details 1-2-3) Check that the drain pipe covers are
present; then position the tank under the spout and proceed
with the positioning of the duckboard adjacent to the side wall.
(
38, details 4-5-6) Position the bench against the side wall
and connect the light cable underneath the cable coming from
the wall, sealing the cable outlet with the foam rubber bushing.
(detail 7) Position the second duckboard.
Installing panels
(
39) Connect the cables to the display, attaching them to
the wall.
(
40, details 1-2-3) Thread the light cables in the corner
hole, connecting them to the electrical box cables indicated.
Thread the foam rubber cylinder to the cables and insert it into
the wall hole.
(
40, detail 4) After having checked all connections, close
the equipment zone, by replacing its cover.
(
40, detail 5) Draw the back support towards the side wall
and install it in such a way that the fasteners at the back can be
inserted into those on the side wall.
NOTE: the sauna panels are made of wood.
(
40, detail 6) Insert the covering panel between the base
wall and the back support and install it in such a way that the
fasteners at the back can be inserted into those on the side wall.
NOTE: the sauna panels are made of wood.
(
40, detail 7) Position the lights behind the panels.
Installing the door glass
If the shower has a door, install the fixed glass and the
glass door; refer to the attached documentation.
(
41, detail 1-3) Insert the plastic rings in the upper and
lower holes in the glass.
(
41, detail 2-4) Assemble the lower and upper hinge, ap-
plying the plates from the inner side of the glass.
21

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Sasha 2.0

Inhaltsverzeichnis