Nstruction Manual; Maintenance - Vitek VT-1835 B Betriebsanweisung

ENGLISH
The brush is intended for collecting of dust from
furniture surface, pile on the brush prevents
damage of polished furniture surface.
I

NSTRUCTION MANUAL

Before using the unit unwind the power cord to the
required length and insert the power plug into the
mains socket. The yellow mark on the power cord
warns about the maximum cord length. Do not
unwind the power cord further than the red mark.
Always switch the vacuum cleaner on only with the
installed dust bin and filters.
• Press the on/off button (13) to switch the vac-
uum cleaner on (pic. 4).
• To wind the power cord press the cord winding
button (14), hold the winding cord with hand to
avoid its whipping and damage (pic. 5).
• Between operations use the brush storage
(15) (pic. 6).
• The unit enables not only dry cleaning, but also
collecting spilled water or drinks.
Attention!
Do not exceed maximal water and dust level
marks in the dust bin (11):
– WATER FILL– maximal allowed water level at
wet cleaning/using the liquid collecting brush
(20);
– DUST MAX – maximal allowed dust and gar-
bage level in the dust bin.
• After room cleaning press the on/off but-
ton (13) and remove the power plug from the
socket.
Filling the dust and garbage bin with water
• Press the button (22) and remove the dust bin
(11) (pic. 7).
• Take the dust bin lid handle with one hand and
the dust bin handle with the other, and then
turn the lid till the mark
• Remove the dust bin lid (23) with the separator
(26) from the flask (27).
• Fill the dust bin (11) with tap water not exceed-
ing the WATER FILL mark.
Note: There is a float (28) inside the removable
flask (27), which allows to control the water level
in the flask. If you are collecting spilled liquid and
its level exceeds the maximal level mark WATER
FILL, the vacuum cleaner will be switched off
automatically.
• Set the dust bin lid so the arrow on the lid (23)
↓ matches the mark
(27) and turn the lid till the mark .
VT-1835_IM.indd 6
(pic. 8).
on the removable flask
6
• Install the dust bin (11) back to its place.
Note: You can perform dry cleaning, but there
should be no water in the flask (27).
• Remove dust and garbage from the dust bin
(11) after every use of the vacuum cleaner.
• Using of vacuum cleaner for collecting foam
being formed during or after processing of
carpets and soft furniture with stain remov-
ers and special detergents is possible only af-
ter adding of a special foam neutralizing agent
for wet and dry vacuum cleaners into the con-
tainer. Follow the dosage as recommended by
the manufacturer.

MAINTENANCE

• As the water in the dust bin (11) becomes dirty,
change it; this procedure is described in the
chapter «Cleaning of the dust bin».
Note: it is recommended to pour out dirty water
from the dust bin (11) and to wash it and the
removable parts the dust bin (11) after every use
of the vacuum cleaner.
VACUUM CLEANER MAINTENANCE
Cleaning of the dust bin
Attention! Provide that the filter (25) is always
clean, because the overall performance of
the vacuum cleaner depends on it; clean the
filter (25) no less than 3-4 times a year, and
more often at severe obstruction.
• Before removing the dust bin (11) switch the
vacuum cleaner off by pressing the on/off but-
ton (13) and take the power plug out of the
mains socket.
• Press the button (22) and remove the dust bin
(11) (pic. 7).
• Take the dust bin lid handle with one hand and
the dust bin handle with the other, and then
turn the lid till the mark
• Remove the dust bin lid (23) with the separator
(26) from the flask (27).
• If some water remains in the removable flask
(27), pour it out.
• Pull the the upper lid lock (24) and open the
upper lid.
• Remove the filter (25) and clean it from dust.
• Wash the removable flask (27), filter (25) and
separator (26) under running water.
Notes:
– Dry all the parts thoroughly before assembling
the dust bin.
– Do not wash the filter (25), the separator (26)
and the removable flask (27) in a dishwash-
ing machine.
(pic. 8).
26.02.2014 9:38:00