YATO YG-20013 Bedienungsanleitung Seite 6

PARTS LIST
1. grill bowl
2. grill cover
3. grill base
4. wheel
5. left shelf
6. right shelf
7. drip tray
8. drip container
9. coupling
10. grate
11. upper shelf
12. grill cabinet
13. burner knob
14. spark generator
15. burner cover
16. gas connection
17. gas hose
18. pressure regulator
19. set of bolts and nuts for grill assembly
SAFETY INSTRUCTIONS
Use only in the open air. Due to the possibility of gas accumulation, which can lead to fi re or
explosion, the grill can only be used in the open air. It is forbidden to use the grill in garages, halls
or other premises. The grill should not be exposed to precipitation.
Please read the Manual before using the appliance. Following the provided instructions can
protect the user against injury, causing fi re or an explosion. Please keep the Manual throughout the
service life of the grill. On handing the product over to any third persons, it must be handed over
with the manual.
WARNING: the accessible parts of the appliance can become very hot. Please keep the chil-
dren away from the appliance. Using the appliance, please remember that the parts of the appli-
ance become very hot because of the fl ame. Please use protective gloves against heat and hold
only by the handles provided for this purpose.
Do not move the appliance when it is in operation. Moving the appliance during its operation can
cause its tipping over, which creates a serious risk of burns and fi re. During movement, the fl exible
hose joining the gas cylinder with the grill may get ruptured, which can lead to an uncontrolled gas
fl ow and cause fi re or explosion.
After use, the valve on the gas cylinder must be closed. Closing the valves situated on the grill
does not result in cutting the gas fl ow to the grill off . Leaving the installation under pressure can
cause an uncontrolled gas fl ow, which results in the risk of fi re or explosion.
Do not alter the structure of the appliance. The manufacturer is able to guarantee safety only
when the grill is assembled in accordance with the recommendations. Improper modifi cations can
cause an uncontrolled gas fl ow which results in the risk of fi re or explosion.
THE GRILL ASSEMBLY
Due to the risk of injury, please take care during the assembly of the grill. Use protective gloves.
The grill assembly described below must be carried out in a brightly lit room.
Mount the wheels in the corners of the base using the bolts (II).
Mount the sides of the cabinets on the base using the bolts (III).
Make the walls rigid with the back wall fi xed with the bolts (IV).
Fix the magnet holding the closed door on the bottom of the base with the bolts (V). Do not tighten
the bolts to make the magnet movement possible, which will come in handy during the adjustment
after mounting the doors.
Fix the magnet to the front coupling using the bolts (VI). Do not tighten the bolts to make the magnet
movement possible, which will come in handy during the adjustment after mounting the doors.
Fix the rails supporting the grill bowl to the top edge of the side walls, using the bolts (VII).
Fix the coupling with the magnet to the side walls using the bolts (VIII). The magnet should be
mounted from the bottom of the coupling.
Fix the handles to the doors, using the bolts (IX).
Screw the hinge rods into the bottom edge of the doors (X).
Mount the doors at the front of the grill cabinet. Insert the hinge rods into the holes in the grill base.
While the rods with fl at belts are inserted through the holes in the top edge of the top coupling and
through the holes in the upper edges of the doors (XI).
Mount the bracket for the container for rendered fat to the inside wall on the right, looking from the
grill front, with the bolts. Then place the container for rendered fat on the bracket (XII).
Place the tray for rendered fat over the container in such a way that the opening in the tray is over
the container (XIII).
Fix the metal sheet cover from the bottom of the grill bowl, using bolts (XIV).
Place the grill bowl on the rails and fi x it with the bolts (XV).
The side walls of the bowl are provided with holes for the installation of the side shelves. Drive bolts
into the upper holes so that the heads of the bolts are a few millimetres away from the side walls
of the bowl (XVI).
Hang the side shelves of the grill on the protruding bolt heads, and fi x them with the bolts. Tighten
the upper bolts and drive, and tighten the lower ones (XVII). Each shelf is fi xed with four bolts.
Mount the side burner gas hose on the side burner inlet nozzle and secure with the snap ring
(XVIII).
Connect the wire terminal to the spark generator contact (XIX).
Mount the rear panel to the rear of the grill cabinet, using bolts (XX).
Place the thermometer in the hole in the cover and fi x with a nut (XXI).
Install a cover over each burner inside the grill bowl. The cover has notches at the edges that must
be aligned with the projections inside the grill bowl (XXII).
Place the grate on the embossment of the grill bowl (XXIII). Mount the additional shelf in the upper
part of the bowl (XXIV).
The side burner is equipped with a wire stand to place the vessel on. The base can be fi xed with a
plastic band for the transport. Cut the band and place the cover so that it is parallel to the ground
(XXV).
6
GB
O P E R A T I N G
USING THE GRILL
WARNING! During use, the appliance must be kept away from combustible materials.
WARNING! While using the grill, protective gloves against burns must be worn.
WARNING! On connecting the gas cylinder and using the grill, it is forbidden to smoke or
approach with open fi re.
The intended use of the grill
The grill is provided for preparing meals in the open air. The product is intended for use solely by
private persons and must not be used in trade or for commercial applications.
It is forbidden to use a fuel diff erent from that listed in the manual. It should not be used for heating
rooms or for heating products other than meals. The main grate is provided for preparing meals by
placing them directly on it. It is forbidden to place vessels such as pots or pans on the grate. The
side burner is used to heat meals in vessels and it is forbidden to prepare meals directly on the
grate of the side burner.
Technical data
Product name: Gas grill
Product catalogue number: YG-20013
Input heat power: 17,5 kW (1270 g/h) (4 x 3,5 kW + 3,5 kW)
Type and pressure of the fuel gas: butane G30 and propane G31 at 37 mbar pressure
Gas appliance category gas according to EN 498: I
Gas supply mode: 11 kg gas cylinders; maximum cylinder dimensions are: 310 mm diameter and
600 mm in height, measured with the valve installed.
Number of burners: 3 main burners + 1 additional burner
Nozzle diameter: 0.86 mm
Dimensions of the main grate, L x W: 600 x 462 mm
External dimensions of the grill with the cover closed, L x W x H 1400 x 580 x 1310 mm
Manufacturer and Authorized Service: TOYA S.A. ul. Sołtysowicka 13-15, 51-168 Wrocław, Poland
Remarks concerning the assembly of the grill
It is forbidden to alter the structure of the grill by the user. Do not remove the factory mounted and
factory sealed elements, the gas installation in particular.
For the side burner, adjustment of the spark generator may be necessary before the fi rst use of
the grill. The spark must jump from the spark generator to the holes in the burner. Otherwise, the
spark generator may fail to ignite the gas properly or at all. If necessary, bend the spark generator
pin, using a small force. All adjustments of the spark generator must be performed with the gas
cylinder disconnected.
Preparing the grill for use
Make sure that the grill has been assembled according to the manual. Place the grill and the cylin-
ders on a fl at, even and non-fl ammable surface. If the wheels have been equipped with a lock, use
it to immobilize the grill. Make sure that there are no fl ammable objects near and above the grill or
other sources of fi re or heat. Keep at least 1 m free space around the grill, and there must be no
objects above the grill.
Attention! Check whether all the knobs of the grill gas burners are in the off position.
Connect the grill to the gas cylinder using the fl exible hose and the pressure regulator. Both the
regulator and the hose must be purchased separately. The pressure regulator in the above sets has
been confi gured to reduce the gas pressure according to the requirements in Poland. The pressure
regulator must meet the requirements of European standard EN 16129. If the pressure regulator is
factory connected to the hose, do not modify this connection.
Place a metal hose clamp on the free end of the hose and then slide the end of the hose to the
connection terminal on the grill (XXXVI). Secure the connection by tightening the hose clamp. Do
not over-tighten the clamp, but only to a degree ensuring a tight connection. Tightening the clamp
too strong may cause the damage to the hose. The pressure regulator is equipped with a threaded
connection that has to be screwed upon the gas cylinder valve using a spanner (XXXVII). Place
the gas cylinder in such a place that the fl exible hose is not bent, twisted or excessively tensioned.
Before connecting, check the hose for damage or wear. If damage or wear of the gas hose is
found, have it replaced for a new one, delivering the grill to the authorized repair shop. Unassisted
replacement of the hose or replacing it with a hose not intended for gas transport is forbidden. The
hose should be 80 cm long, and its length must not exceed 150 cm. Use only fl exible hose intended
for liquid propane or butane gas transport. After the connection has been made, check the tightness
of the gas installation.
If the local regulations require the application of another hose and/or regulator, they must be pur-
chased separately to meet the requirements for the given place of use.
Under normal operation conditions, it is recommended to replace the correctly installed pressure
regulator every 10 years from the year displayed on the regulator. Local regulations can require
other regulator replacement periods. While using the pressure regulator outdoors, it must be placed
and secured in such a way that no water can enter it. During the operation, provide good ventilation
to the pressure regulator, which will prevent condensation inside the equipment. The pressure
regulator is confi gured to operate in the ambient temperatures from -20 up to +50 deg. C. If the
pressure regulator has been installed behind another regulator, the pressure in the installation must
be adjusted to be within the input pressure range supported by the regulator attached to the grill.
Due to the proximity of the burners, it is forbidden to place the gas cylinder on the bottom shelf of
the grill. The gas cylinder must be positioned vertically. Before connecting, remove the protective
fi lm (seal) from the gas cylinder valve, check the condition of the gasket, and, if no damage or wear
have been found, screw the nut of the pressure regulator to the gas cylinder valve. The connec-
tion must be tightened with the force necessary to achieve tightness. Excessive tightening of the
connection may damage the gasket and the connection will not reach the required tightness. It is
forbidden to install the pressure regulator to the valve with a damaged gasket. In such case, obtain
the information necessary to replace the gasket from the gas cylinder manufacturer.
Open the gas cylinder valve slowly until reaching full opening and check the connections for leaks.
WARNING! If there is a sound of escaping gas already audible while opening the gas cylinder valve,
and the door of the gas is strongly perceptible, close the gas cylinder valve immediately. Check
whether the valves of the gas burners are closed and then check the tightness of the connections.
WARNING! It is forbidden to check the connection for gas leaks with fi re. There's a risk of burns, fi re
or explosion. Use commercially available electronic or chemical testers. Please read the attached
instructions before using them.
You can also prepare a soap-water mixture containing ca. 1/4 of soap and 3/4 of water and cover
the gas installation with it. Visible gas bubbles indicate the place of the leak in the installation. If
the leak is observed, close the gas cylinder valve and remove the leak, e.g. by tightening the con-
nections. Repeat the check for leaks. If the leaks cannot be removed, close the gas cylinder valve,
disconnect the cylinder from the grill, and deliver the grill to the authorized repair shop.
I N S T R U C T I O N S
3B/P(37)