Maintenance; Operation - Electrolux SEA65 Installations, Gebrauchs Und Wartungsanweisungen

Single phase electric supply
Frequency
Max. power input:
- model SEA45
- model SEA65
Positioning
• The salamander can be installed on shelf or no stand
according to the space available and the manner of use.
• Slowly remove the appliance protective film without
tearing it, for the glue could remain on the appliance outer
casing. Should this happen, remove the glue using a
suitable solvent.
Power Supply
• The appliance operates on a 220 V single phase - 50 Hz
power supply. Therefore, in order to connect the appliance
to its power supply, it will be necessary to provide the
power supply cable with a normalized plug suitable to the
absorbed load and then to connect it to a proper main
socket, while making sure that in this last there is an
efficient earthing contact.
• Between main socket and electric supply line it is
necessary to insert an automatic suitable circuit breaker
that, when switched off, between its stationary and
movable contacs there is a gap of at least 3 mm.
The Manufacterer disclaims any liability in case these
accident-preventing rules are not observed.
INSTRUCTIONS FOR THE USER
Note: This machine has been built according to the EEC
regulations 82/489 for the suppression of
radiodisturbances.

OPERATION

Preleminary
The salamander is suitable for normal and "au gratin"
cookings or for warming up the food by means of the
irradation coming from a high temperature heating source
placed over the food to be cooked.
The appliance is equipped with a device which allows to
lift or lower the radiant plate "C" (fig. 1) in order to heat
the food more or less respectively.
The heating system consists of one heating element on
model SEA45 and, on model SEA65, of two groups of
heating elements the temperature of which is individually
controlled by an energy regulator.
To start the machine (fig. 1)
• Switch on the automatic circuit breaker on the supply
line back of the appliance.
• Turn
the energy
anticlockwise on the setting corresponding to the desired
V
Hz
Kw
Kw
regulator control knob
temperature bearing in mind that the higher the number the
220 higher the temperature.
50/60 The signal lamp "B" indicates when the heating is on. The
heating elements will turn on automatically as soon as the
2,0 temperature sinks below the chosen temperature value and
3,8 will turn off whenever the temperature reaches its selected
value. On the setting "∞" the heating elements are kept
always on for the utmost temperature.
Switching off (fig. 1)
• Turn the control knob of each energy regulator to the
setting "0".
• Switch off the circuit breaker on the electric supply
line.

MAINTENANCE

The maintenance must be always carried out with the
appliance electrically switched off.
• At the end of each cooking cycle, careful clean the grid
and the pan for collecting the sauces.
• Daily clean the stainless steel surfaces with luke warm
soap water, then rinse them again and again with fresh
water and wipe them thoroughly.
• Do not use steel wool, wire brushes, or similar abrasive
cleaning material on these parts as damage can occur.
Stainless steel wool can be also used but it is necessary to
rub the surfaces always on the direction of the stainless
steel satin finish.
• Apply a thin layer of vaseline oil on all steel surfaces in
the event of the machine not being used for any length of
time. Periodically air the room in which the appliance is
installed.
Caution
Do not wash the appliance with direct or high pressure
water jets since possible leakings on the electric
components might prejudice the regular working of the
machine as well as the safety devices.
INSTRUCTIONS POUR L'INSTALLATEUR
Les opèrations d'installation et de raccordement de
l'appareil doivent être exécutées par un technicien qualifié
d'après les régulations en vigueur.
Note: La plaque de caractéristiques se trouve à droite de
la partie postérieure de l'appareil.
Données techniques
Alimentation èlectrique monophasée
Fréquence
Puissance max. absorbeé:
- modèle SEA45
- modèle SEA65
"A"
Emplacement
4
V 220
Hz 50/60
Kw 2,0
Kw 3,8