Installation - HQ Power VDP900HZ Bedienungsanleitung

4. Ins tallation
x Remov ve all packing m aterial from the
remove ed.
x Clean t the spray nozzle e and make sure
he VDL900HZ
x Place t horizontally on
x Pour hi igh quality smok ke liquid (VDLH
fluid lev vel. Do not ove rfill. Place the c
x Connec ct the remote co ontrol into the s
5. Use e
a) The Device
x Plug th he remote contro ol into the slot a
power cord.
x Turn on n the power swi itch located at t
x The red d light on the re emote control w
x The de vice must warm m up. The period
minute es.
x The gre een light on the e remote control
Remot te Control").
b) The Remote Contr rol
Please re efer the illustrat ion on page 2.
1
pow wer LED
smo oke output ever ry x minutes (m
2
30 min)
3
out put volume
4
fixe ed time open LE ED
6. Not tes
The V VDP900HZ doe es not feature a
pum p will continue e working. Alw
device can su
x If you e experience low output, mechan
Check the fluid level, t the external fus
working g properly, plug g in the unit aga
operati ion to avoid per rmanent damag
before transporting th e unit.
x Using t the device will p produce water d
x A little smoke may con ntinue to escape
7. DMX X Connectio on
a. DMX5 12 Connection n
Connect an XLR cable to o the female 3-p
nput of the VDP P900HZ. Multip
pin XLR i
cable sho ould be a two-co ore screened ca
b. DMX-5 512 Chain with h Termination
c. DMX S Start Address
All DMX-c controlled devic ces need a digita
This start t address is the channel numbe
Enter the e correct numbe er and read it fro
You can u use the same st tarting address
device.
09.11.201 0
VDP90
e shipping box. C Check that all fo
e nothing is obs structing the ou
a flat surface. R Remove the liqu
HLH5) into the t
tank, being care
cap back on the
slot at the back
at the back of th he device. Plug
the back of the device.
will light up.
d depends on th he conditions bu
l will go up once e the machine is
5
max.
6
7
8
an automatic stop function
ways monitor t the tank fluid
uffer damage w
nical noise or no o output at all, u
se, the remote c control and the
ain. If the device e will not functi
e. Return the de evice to your de
rops at the noz
e from the nozz zle after operatio
pin XLR output o of your controlle
ple VDP900HZs
s can be linked
able with XLR in put and output
n
A DMX term minator is recom mmended for ins
to run a lon g distance or is
The termina ator prevents co orruption of the
noise. The D DMX terminator
between pin ns 2 and 3, whic ch is then plugg
the last dev vice in the chain
al start address
er from which th he device starts
om the display
for a whole gro oup of devices o
4
0HZ
oam and plastic
tput.
uid tank cap.
eful not to excee
liquid tank and tighten.
of the device.
the device into
ut should not tak
s ready to opera
output LED
successive s spraying for x se
seconds)
heated over r LED
spray button n
when running
level during o
when run with hout fluid!
unplug the devi
power cord. If a
on after 30 seco
ealer. Remembe
zle. This is perf fectly normal.
on.
er and the other
through serial l
connectors.
tallations where
in an electrical ly noisy environ
digital control s
is simply an XL LR plug with a 1
ged into the XLR
. Please see illu ustration.
so that the cor rrect device resp
s to "listen" to th
base of the VDP
located on the b
r enter an indiv
c padding is
ed the maximum m
the mains usin g the
ke more than 10 0
ate (see "The
econds (max. 1 5
g out of fluid; t the
operation as th he
ce immediately .
all appears to be e
onds, discontinu ue
er to drain the t tank
r side to the ma ale 3-
inking. The link king
e the DMX cable e has
nment (e.g. disc cos).
signal by electri cal
120 resistor
R output socket of
ponds to the sig gnals.
he DMX controll ler.
P900HZ.
vidual one for ev very
©Vellema an nv