Receptarea semnalului DCF
Dacă bateriile din staţia meteo sunt bine încărcate, are loc receptarea semnalului DCF şi reglarea automată
a orei. Ceasul receptează semnalul radio DCF în fi ecare zi la ora 02:00 şi concomitent are loc actualizarea orei. După
încetarea receptării şi reglarea orei apare icoana emiţătorului
Avertizare: În timpul recepţionării semnalului DCF nu folosiţi nici un fel de butoane! Recomandăm reglarea orei
în timp de noapte, când semnalul DCF se propagă mai bine.
Iniţierea manuală a recepţiei semnalului DCF
Receptarea semnalului DCF se poate iniţia oricând prin apăsarea butonului RCC. Ceasul începe să detecteze şi să
recepteze imediat semnalul DCF timp de 6-16 minute. Icoana emiţătorului va clipi.
Pentru întreruperea receptării apăsaţi lung butonul RCC.
Eşuarea receptării semnalului DCF
Dacă nu se realizează automat reglarea ceasului la ora 02:00, sau după apăsarea butonului RCC, este necesară
mutarea ceasului în alt loc ori reglarea lui manuală.
Reglarea manuală a orei
1. Apăsaţi şi ţineţi butonul DISPLAY SET timp de 3 secunde – începe reglarea orei.
2. Cu butoanele + ori – selectaţi afi şarea orară de 12/24.
3. Cu butonul DISPLAY SET confi rmaţi formatul orar setat, treceţi la reglarea orei.
4. Cu butoanele + - reglaţi ora actuală, cu butonul DISPLAY SET avansaţi treptat la valorile ora – minuta - secunda.
5. Confi rmaţi prin apăsarea butonului DISPLAY SET, treceţi la reglarea fusului orar (zona orară). Cu butoanele
+ - selectaţi şi, apăsând DISPLAY SET, încheiaţi reglarea.
Reglarea alarmei
1. Apăsaţi şi ţineţi butonul ALARM SET timp de 3 secunde.
2. Cu butoanele + ori – reglaţi ora alarmei.
3. Selectaţi ora, apoi prin apăsarea butonului ALARM SET selectaţi minutele.
4. Reapăsaţi butonul ALARM SET şi încheiaţi reglarea. La o altă apăsarea a butonului ALARM SET apare icoana
clopoţelului – alarma este reglată.
Prin reapăsarea butonului ALARM SET anulaţi activarea alarmei – icoana clopoţelului nu va fi afi şată.
Activarea funcţiei SNOOZE – alarmă repetată
1. După declanşarea alarmei, staţia meteo începe să sune. Peste două minute alarma se opreşte automat şi rămâne
reglată pentru ziua următoare la aceeaşi oră.
2. Prin apăsarea butonului SNOOZE/LIGHT sunetul se întrerupe şi se amână cu 5 minute.
3. Funcţia SNOOZE/LIGHT o anulaţi prin apăsarea butonului ALARM SET pe partea din spate.
Avertizarea asupra poleiului
1. În caz că temperatura exterioară scade între valorile -2°C la +3°C (28°F - 37°F), pe ecran apare icoana
şi începe să clipească regulat.
2. Icoana
dispare imediat ce temperatura exterioară creşte peste limita menţionată.
Activarea luminii de fundal a ecranului
Lumina de fundal a ecranului se poate activa prin apăsarea butonului SNOOZE/LIGHT, care activează iluminarea
pe 5 secunde. Folsirea frecventă a iluminării reduce viabilitatea bateriilor.
Prognoza vremii
Staţia prognozează vremea pe baza modifi cărilor presiunii atmosferice pe următoarele 12 – 24 ore pentru împrej-
urimi la 15 – 20 km distanţă.
Precizia prognozei vremii este de 70 %.
Icoana prognozei vremii este afi şată în partea de sus a ecranului.
Întrucât prognoza vremii nu poate fi întotdeauna exactă 100%, producătorul şi vânzătorul nu poate fi responsabil
pentru orice daune cauzate de prognoza inexactă a vremii.
La prima reglare sau resetarea staţiei meteo durează aproximativ 12 ore până ce staţia începe să prognozeze corect.
Staţia meteo afi şează 4 icoane privind starea vremii.
E8404-navod-A6.indd Spread 3 of 22 - Pages(42, 3)
E8404-navod-A6.indd Spread 3 of 22 - Pages(42, 3)
. În acest caz reglarea manuală nu este necesară.
42
GB
WIRELESS WEATHER STATION C8404C
+ SENSOR (433 MHz)
Description and technical parameters
- weather forecast icons
- hours, minutes, seconds, alarm clock and snooze function, inner and outer temperature (°C/ °F)
- automatic time update thanks to a radio signal from Mainfl ingen in Germany on the frequency 77.5 kHz (DCF77)
- 12/24 hour time format
- temperature measurement range: inner -40°C to +70°C +/-1°C; outer - 40°C to 70°C +/-1°C
- temperature measurement precision: 0.1°C
- operating temperature: 0°C - 45°C
- temperature units: °C/°F
- temperature measurement interval: every 60 - 64 seconds
- outer temperature broadcast: every 60 - 64 seconds
- outer wireless sensor: 433 MHz
- broadcast range: max. 50 m in free space without interference
- power supply: weather station: 2 x 1.5 V, type AA (alkali batteries recommended)
wireless sensor: 2 x 1.5 V AA (alkali batteries recommended - for temperatures below 0° C or above 50 °C
it is suitable to use lithium batteries - their service life is longer)
- dimensions: weather station with a clock 84 x 139 x 47 mm; wireless sensor 65 x 100 x 35 mm
Layout of the main elements and buttons
Weather station with a clock (main unit – receiver)
1 - LCD display
5 – button MEM/-
2 – button SNOOZE/LIGHT
6 – button DISPLAY SET
3 – button ALARM SET
7 – sliding button °C/°F
4 – button CH/+
8 – button SENSOR
Sensor
1 – LED indicator
3 – channel toggle (1, 2, 3)
2 – RESET button
4 – opening to hang on the wall
Commissioning
Insert batteries into the weather station and the wireless sensor. Do not combine old and new batteries nor diff erent
types of batteries (alkali, carbon-zinc, nickel-cadmium) and do not use rechargeable batteries! Proceed as follows:
1. Open the cover on the rear cover of the weather station and on the rear side of the sensor.
2. Insert 2 batteries, 1.5V, type AA into the weather station and then 2 batteries 1.5V, type AA to the sensor. Maintain
proper polarity of the inserted batteries according to the schematic on the bottom of the battery compartment!
3. Close the cover.
4. First push the RESET button on the main unit and then push RESET under the cover of the sensor.
Reception of temperature data from the wireless sensor of from multiple sensors.
1. First push RESET on the main unit and then push RESET under the sensor cover. Within 15 minutes the informa-
tion about outer temperature will be received.
2. Within 5 minutes after reception of the sensor signal there will start a search for the DCF signal.
3. Inner temperature is shown on the display down next to the icon
in the middle next to the icon with the sensor number (1, 2, 3)
4. You can set the sensor channel by using the sliding button on the sensor. On the weather station you push the CH/+ button.
5. If you have attached more sensors, you can switch the display of temperature from diff erent sensors manually
or automatically. When switching manually, you just push the CH/+ button to toggle to temperature display
from the required sensor. To automatically switch to the display of temperature from individual sensors, hold
the CH/+ button for 3 seconds. To end the automatic switching mode, hold the CH/+ button for 3 seconds again.
9 – button RCC
10 – button RESET
11 – battery compartment
5 – battery compartment
. Outer temperature is shown on the display
.
3
2.8.13 13:55
2.8.13 13:55