Installing The Hood - Sirius S-DD2 Bedienungsanleitung

2/ INSTALLING THE HOOD

1) Before starting the appliance installation, please check that all components are not dam-
aged, in such a case contact your retailer and do not carry out installation.
Furthermore, please read carefully all of the following installation instructions.
- Use an exhausting pipe whose maximum length does not exceed 5 meters.
- Limit the no. of elbows in the piping , since each elbow reduces the aspiration efficiency
of 1 linear meter. (Ex. : if you use no. 2 x 90 ° elbows, the length of piping l must not
exceed 3 meters)
- Avoid abrupt direction changes.
- Use a 150 mm constant diameter pipe for the whole length .
- Use piping approved by standards in force.
Before the installation of the Downdraft, please remove the security piece you can see in
the picture (Fig. 1-2-3-4).
The manufacturer will not be answerable for any capacity or noise problems caused by fail-
ure to comply with the above instructions and the warranty will be rendered null and void.
2) Before making the opening, check that there are no structural or other parts inside the
cabinet, where the appliance is to be placed, which could hinder a proper installation.
Check that the dimensions of the Downdraft and the ones of the cooktop are compatible
with the cabinet so that the installation can be carried out properly.
3) Make a rectangular opening, 790 x 100 mm in size, in the back of the cook top for the
90 cm model and 490 x 100 mm for the 60 cm model and 1090x100mm for the 120cm
model.
For models with motor already fitted, remove the screws and the extraction unit to fit the
downdraft in the relevant hole. At this point, insert a seal (silicone) in the bottom section
of the frame support (Fig. 18) and place in the relevant hole (Fig. 18-19-20), then proceed
to insert the downdraft into the unit.
4) Put the Downdraft in the opening, inserting it from above as shown in Fig. 12.
5) Fix the downdraft inside the cabinet, using the special fixing brackets supplied with the
product. (Fig.13a).
Insert the brackets in the lower side of the downdraft (Fig.13b), in such a way that there is a
2 mm distance between the lower side of bracket and the bottom of the cabinet. (Fig.13c).
This distance will allow the traction to be positioned downwards of the product, at the mo-
ment of fixing, in order to have the stainless steel trim perfectly adhering with the work
surface.
Before inserting the screws, please make sure that the appliance is perfectly perpendicular
with the work surface.
6) After completing the installation and connecting the appliance to the mains electricity, lift
the downdraft and remove the door block (Fig. 5-6-7). Then open the door (Fig. 8 - 9),
remove the PVC grease filter shield (Fig. 10), then place the filters as illustrated in Fig. 11.
7) In the version of the Downdraft equipped with motor, install the motor group adjusting the
air evacuation direction as required, either downwards or upwards. After installing the mo-
tor, connect the air ducts (Fig. 13). The motor can be fitted either on the front or back side
of the downdraft.
8) For versions with outside motor, place the suction unit (outside motor) in a suitable area
and fit the exhaust air flue as illustrated in Fig. 13. Proceed to fit the air outlet ducts be-
tween the outside motor and the down draft. Select an air outlet from the five possibilities
(Fig. 21) and fit the connection provided.
9) Put the metallic box containing the electronic components in a place easy to be reached if
a technical assistance is needed (Fig. 14). Connect the electrical connectors of the box to
the Downdraft (Fig. 14).
Connect the internal motor or the external motor's cable to the terminal board found inside the plastic box of the
10) For outside motors, connect the motor unit cable to the relevant connector on the electrical
components box. downdraft wiring . Make sure to respect the colors of cables when performing the electrical connection (fig.25)
11) Power the appliance.
Downdraft calibration
After having installed the Downdraft, it is necessary to start the calibration procedure, which
is aimed at adjusting the extraction strength of the filtering unit. Connect the product to
the power line, making sure that it is conformed to the supply voltage indicated on the
technical data tag.
18
EN