Installation; General Instructions; Unit Characteristics - TECNOINOX PC35G7 Handbuch

Part 1
GAS COOKTOPS
The appliance described in this manual has been built to meet UNI
EN 203 and UNI EN 437 standards.
This appliance has been designed exclusively for cooking food, any
other use is considered improper. It should only be used by qualified
personnel in professional kitchens.
The appliance should be installed under an extractor hood for removing any cooking fumes.
Care must be taken when using the appliance because the cooking surfaces are very hot.
The appliance must be installed, connected and serviced properly by qualified personnel according to the regulations and
directives in force in the country where it is installed, as well as the instructions in this manual.
This instruction manual refers to the installation and use of the
Category II2H3+ gas cooktops.
The self-adhesive polyester data plate "T" (fig.2) is behind the
control panel (inside the appliance).
It contains the following information:
Model
Serial number:
Category:
Year of construction:
Nominal thermal capacity:
Type of construction:
Test base:
G30
Connection pressure:
G20
G30
Consumption:
G20
Before you install the appliance, make sure that the
gas company has authorised the installation,
compare the data relevant of the appliance (data
plate) with the local supply.
Remove the packaging from the appliance as well as the protective
plastic sheet, and, if necessary, remove traces of glue with a suitable
solvent. To dispose of the packaging, follow local directives (for more
details refer to the chapter "ECOLOGY AND THE ENVIRONMENT".
Prior to connecting the unit to the gas network, check the data plate
to see if the unit has been set and tested for the type of gas supplied.
If the gas type indicated on the data plate is not the same as that
supplied, please refer to the paragraph "CONVERSION AND
ADAPTATION".
Connect the appliance to the gas distribution network using metal
pipes with a suitable diameter; install a homologated on/off cock
between the appliance and the distribution network. If flexible pipes
are used they must be made of stainless steel according to the
standards in force. When installing the appliance, all the regulations
in force must be observed, such as:
PC35G7 PC70G7 PC105G7
xxxxxx
II2H3+
XXXX
10.5 kW 19.5 kW
A
UNI EN 203-1
28-30/37 mbar
20 mbar
0.83 Kg/h 1.54 Kg/h 2.36
1.11 m 3 /h 2.06 m 3 /h 3.17
Connection to the distribution network

General Instructions

The unit must never be left unattended when it is being used! The
appliance should be checked once a year by a qualified technician.
Switch the appliance off in the case of a failure or malfunction.

Unit characteristics

The supplementary plate is also made of self-adhesive polyester and
is affixed near the data plate; it contains all information regarding the
appliance.
Both the appliances have a fitting for gas connection. The "G" gas
distribution network connection (fig.1) meets ISO 7/1 and ISO 228/1
(DK) standards with a ø ½" connection, situated at the back of the
machine.
Model
PC35G7
PC70G7
PC105G7
PCP70G7
PCP105G7
30 kW
PPC70G7
The structure of the appliance is made of stainless steel, the burners
are made of cast iron and the oven is made of stainless steel. All
models have adjustable feet.
The main gas pipe is made of galvanised steel. The pipes between
the tap and burner are made of copper.
Kg/h
m 3 /h
WARNING! Install a shut-off cock in the line between the
appliance and the gas distribution network.
■ UNI-CIG 8723 safety standard, Act n.46 of the 5th of March 1990
and circular n.68.
■ Regional and/or local regulations, such as building codes;
■ Accident prevention regulations in force;
■ Fire prevention regulations;
■ Applicable I.E.C. regulations.
We recommend installing the appliance in a well-ventilated
environment, or under an extraction hood to remove the fumes or
vapours produced during the cooking cycle.
The appliance can be installed alone or in line.
Respect a minimum distance of 80mm between the appliance and
any walls made of flammable material, partitions, kitchen furniture or
nearby equipment.
The contact surfaces must be covered with non-combustible heat
insulating material.
The appliance must not be installed near heat sources, the ambient
temperature in the place where the appliance is installed must not
rise to over 50°C.
After installing the appliance check for any leaks in the fittings. Use
non-corrosive foam products, such as leak detection sprays, to look
for any leaks.
GB / IE - 1
N. of burners Type
2 Burner
4 Cooker
6 Cooker
2+1 Cooker + hot plate
4+1 Cooker + hot plate
1 Hot plate

Installation

5410.263.00