English - Milwaukee MS 304 DB Originalbetriebsanleitung

i) Cut only one workpiece at a time. Stacked multiple workpi-
eces cannot be adequately clamped or braced and may bind on the
blade or shift during cutting.
j) Ensure the mitre saw is mounted or placed on a level,
rm work surface before use. A level and rm work surface
reduces the risk of the mitre saw becoming unstable.
k) Plan your work. Every time you change the bevel or
mitre angle setting, make sure the adjustable fence is set
correctly to support the workpiece and will not interfere
with the blade or the guarding system. Without turning
the tool "ON" and with no workpiece on the table, move the saw
blade through a complete simulated cut to assure there will be no
interference or danger of cutting the fence.
l) Provide adequate support such as table extensions,
saw horses, etc. for a workpiece that is wider or longer
than the table top. Workpieces longer or wider than the mitre
saw table can tip if not securely supported. If the cut-o piece
or workpiece tips, it can lift the lower guard or be thrown by the
spinning blade.
GB
m) Do not use another person as a substitute for a table
extension or as additional support. Unstable support for the
workpiece can cause the blade to bind or the workpiece to shift
during the cutting operation pulling you and the helper into the
spinning blade.
n) The cut-o piece must not be jammed or pressed by any
means against the spinning saw blade. If con ned, i.e. using
length stops, the cut-o piece could get wedged against the blade
and thrown violently.
o) Always use a clamp or a xture designed to properly
support round material such as rods or tubing. Rods have a
tendency to roll while being cut, causing the blade to "bite" and
pull the work with your hand into the blade.
p) Let the blade reach full speed before contacting the
workpiece. This will reduce the risk of the workpiece being
thrown.
q) If the workpiece or blade becomes jammed, turn
the mitre saw o . Wait for all moving parts to stop and
disconnect the plug from the power source and/or remove
the battery pack. Then work to free the jammed material.
Continued sawing with a jammed workpiece could cause loss of
control or damage to the mitre saw.
r) After nishing the cut, release the switch, hold the saw
head down and wait for the blade to stop before removing
the cut-o piece. Reaching with your hand near the coasting
blade is dangerous.
s) Hold the handle rmly when making an incomplete
cut or when releasing the switch before the saw head is
completely in the down position. The braking action of the
saw may cause the saw head to be suddenly pulled downward,
causing a risk of injury.

English

24
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Wear ear protectors. Exposure to noise can cause hearing loss.
Always wear goggles when using the machine. It is recommended
to wear gloves, sturdy non slipping shoes and apron.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Use a dust absorption system and
wear a suitable dust protection mask. Remove deposited dust
thoroughly, e.g. with a vacuum cleaner.
Connect the saw to a dust-collecting device when sawing wood.
Wear gloves!
Before using the tool please read the instructions. If possible have
the tool demonstrated.
Ensure that the machine is always stable and secure (e.g. xed to
a bench)
Keep the oor area free of loose material e.g. chips and cut-o s.
Do not use saw blades which are damaged or deformed
Do not use saw blades not corresponding to the key data given in
these instructions for use.
Only use tools that meet standard EN 847-1.
Do not use saw blades made of high-speed steel.
It is necessary to select a saw blade which is suitable for the
material being cut.
The rated speed of the accessory must be at least equal to the
maximum speed marked on the power tool. Accessories running
faster than their rated speed can break and y apart.
Transport and store the tools in a suitable receptacle;
Do not use any anges other than those supplied or indicated in
the instruction manual to secure the saw blade.
Never use the mitre saw to cut materials other than those speci-
ed in the instruction manual.
Only use the saw with guards in good working order and properly
maintained, and in position.
Refrain from removing any cut-o s or other parts of the workpi-
ece from the cutting area whilst the machine is running and the
saw head is not in the rest position.
Never reach into the danger area of the machine when it is
running.
Always use the protective shields on the machine.
Any faults with the machine, including any related to the safegu-
ard or the saw blades, must be reported to the persons in charge
of safety as soon as the faults are discovered.
Do not clamp the protective swing guard.
Long workpieces must be adequately supported.
The handle lock must always be engaged when transporting the
mitre saw.
When performing mitre, bevel or compound mitre cuts, adjust the
sliding fence to ensure the correct clearance from the blade.
Adapt the feed speed to avoid overheating the blade tips and to
avoid melting plastic materials during cutting.