Proper Use; Technical Data; Before Starting The Equipment - EINHELL TE-VC 18/10 Li - Solo Originalbetriebsanleitung

•
Flexible suction hose
•
Crevice/brush nozzle
•
Upholstery/universal nozzle
•
Foam filter
•
Additional filter
•
Dirt bag
•
Original operating instructions
•
Safety instructions

3. Proper use

The cordless wet/dry vacuum is designed for wet
and dry vacuuming using the appropriate fi lter.
The equipment is not suitable for the vacuuming
of combustible, explosive or harmful substances.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Motor power supply ................................18 V d.c.
Tank volume: ..................................................10 l
Weight
(without rechargeable battery): ........ approx. 3 kg

5. Before starting the equipment

5.1 Assembling the equipment
Fitting the equipment head (Fig. 4)
The equipment head (3) is fastened to the tank
(7) by the locking hook (6). To remove the equip-
ment head (3), open the locking hook (6) and
take off the equipment head (3). When fi tting the
equipment head (3), make sure that the locking
hook (6) locks into place correctly.
5.2 Fitting the fi lters
Important!
Never use the wet/dry vacuum without a fi lter.
Always ensure that the fi lters are securely seated.
Anl_TE_VC_18_10_Li_Solo_SPK9.indb 17 Anl_TE_VC_18_10_Li_Solo_SPK9.indb 17
GB
Fitting the foam fi lter (Fig. 5)
For wet-vacuuming, slip the supplied foam fi lter
(14) over the fi lter basket.
Fitting the additional fi lter (Fig. 6)
For dry vacuum cleaning always use the supplied
additional fi lter (16). Fit the additional fi lter, so that
no air is sucked through the fi lter cage (4) without
being fi ltered.
Assembling the dirt bag (Fig. 7)
For vacuuming fi ne, dry dirt it is recommended
that you fi t the dirt bag (15). Slip the dirt bag (15)
over the vacuuming hole. The dirt bag (15) is sui-
table for dry-vacuuming only. The dirt bag makes
it easier to dispose of the sucked-in dust.
5.3 Fitting the suction hose (Fig. 1,3)
Connect the suction hose (10) to the correspon-
ding connector on the wet/dry vacuum, depen-
ding on the application required.
Vacuuming
Connect the suction hose (10) to the suction hose
connector (8).
Blowing
Connect the suction hose (10) to the blow con-
nector (9).
5.4 Suction nozzles
Crevice/brush nozzle (Fig. 2)
The crevice/brush nozzle with swing-out brush
(12) is designed for vacuuming solids and liquids
in corners, edges and other areas that are diffi cult
to access.
Upholstery/universal nozzle (Fig. 2)
Fitted with the brush insert (13), the nozzle is
designed for vacuuming solids from upholstery
and carpets. Without the brush insert (13) fi tted,
the nozzle is designed for vacuuming solids and
liquids from small to medium-sized surfaces. To
remove the brush insert, press the button and pull
the brush insert off to the side at the same time.
5.5 Charging the battery (Fig. 10)
1. Take the battery pack out of the equipment.
Do this by pressing the side pushlock buttons.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(d) into the socket outlet. The green LED will
then begin to fl ash.
3. Slot the battery pack (18) onto the battery
- 17 -
06.03.2019 11:08:22 06.03.2019 11:08:22