Gemini CS-19R Bedienungshandbuch Seite 5

CHANNEL 5 INPUT SELECT SWITCH: Allows you to select the input source for Channel 5. Select MIC3, Line 5,
2 1
Line 6, Line 7, Line 8 or AUX. The level and EQ features will affect only the input that is selected for that channel. (MIC #3
input on this channel)
CHANNEL 5 GAIN CONTROL: Adjusts the GAIN for Channel 5. Rotate this knob clockwise to increase the gain to
2 2
the channel. Rotate the knob counterclockwise to decrease the gain to the channel.
CHANNEL 5 HIGH EQ CONTROL: Contour the high frequency response for Channel 5. Rotate this knob clockwise to
2 3
increase the high frequency response, and counterclockwise to decrease it. This gives you a wide variety of sound
possibilities allowing for special effects.
CHANNEL 5 MID EQ CONTROL: Contour the mid frequency response for Channels 1, 2, 3 and 4. Rotate this knob
2 4
clockwise to increase the mid frequency response, and counterclockwise to decrease it. This gives you a wide variety of
sound possibilities allowing for special effects.
CHANNEL 5 LOW EQ CONTROL: Contour the low frequency response for Channel 5. Rotate this knob clockwise to
2 5
increase the low frequency response, and counterclockwise to decrease it. This gives you a wide variety of sound
possibilities allowing for special effects.
CHANNEL 5 SLIDE/KNOB: Controls the relative levels of Channel 5.
2 6
CHANNEL 5 CUE ASSIGN BUTTON: Engaging any single or combination of CUE pushbuttons sends any program present
2 7
at Channel 5's source control SELECT SWITCH to the headphone cue section. The pushbuttons will illuminate
when the switch is engaged.
CROSSFADER: Allows the mixing of one source into another. This crossfader controls the levels of any two channels
2 8
assigned to it by the left and right Crossfade ASSIGN SWITCHES.
LEFT ASSIGN SWITCH: Assigns the left side of the Crossfader to any of the five Input Channels
2 9
RIGHT ASSIGN SWITCH: Assigns the right side of the Crossfader to any of the five Input Channels
3 0
MASTER BALANCE: Adjusts the balance of the Master LEFT and RIGHT channels
3 1
MASTER: Determines the program and mic level at the Main Outputs
3 2
BOOTH CONTROL: Adjusts the level of the Booth Output
3 3
ZONE 1 CONTROL: Adjusts the level of the Zone 1 Output
3 4
ZONE 2 CONTROL: Adjusts the level of the Zone 2 Output
3 5
PREFADER INPUT LEVEL LED METERS: Reflect the Gain, High, Mid & Low adjustments
3 6
LOOP INPUTS: Brings the signal back to the mixer from an outboard signal processor
3 7
LOOP OUTPUTS: Sends the signal out from the mixer to an outboard signal processor. The unit comes with jumpers to be
3 8
used with the loop inputs and outputs. Keep the jumpers in the unit if you are not using the loop to prevent interruptions in
your music program.
AUX INPUTS: Allow easy access for connecting an additional device (tape deck, etc.). This is a useful feature if you need to
3 9
connect another sound source temporarily. You do not have to disconnect any of the devices you already have connected to
use an additional device.
CROSSFADER CURVE BUTTON: The CROSSFADER CURVE BUTTON allows you to adjust the kind of curve the
4 0
crossfader has. Depress the CROSSFADER CURVE BUTTON to make the curve steep and cutting (perfect for
scratching). Release the CROSSFADER CURVE BUTTON to make the curve gradual and gentle.
CUE BUTTON: When you press the CUE BUTTON you will send your cue mix (the same mix you hear in your
4 1
headphones) to the booth monitors.
LOOP BUTTON: Activates the LOOP inputs and outputs. When activated this pushbutton will illuminate.
4 2
MIC OVERLOAD LEDS: Light if the signal to MIC inputs 1 & 2 is too high. When these LEDs light, you should reduce the
4 3
gain of that channel to prevent distortion.
MASTER OUTPUTS (BALANCED): Uses XLR connectors. Provides a fully balanced main output signal. Pin 2 is (+), pin 3
4 4
is (-) and pin 1 is signal ground. Use these outputs to connect to your main amplifier and speaker system.
MASTER OUTPUTS (UNBALANCED): Provides main output signal using RCA connectors. Use these outputs to connect
4 5
to your main amplifier and speaker system.
BOOTH OUTPUT JACKS: Used to connect to amplifier in the DJ Booth. Uses RCA connectors.
4 6
Page 5