9. Product Return ..............7 10. Technical Assistance ............7 11. Appendix A Tube Loading Capacity......7-8 ® 12. Appendix B MASTERFLEX Two-Stop Tube Sets ..7-8 Figure 1. Pump Heads SAFETY PRECAUTIONS WARNING: Tubing breakage may result in fluid being sprayed from pump. Use appropriate measures to protect operator and equipment.
Tool required: long hex key (provided) reference. You can go directly to a particular section and Mount the pump head to a MASTERFLEX L /S pump drive as quickly find the answers. Appendix A (See page 8) lists tubing follows:...
Pump Head. Tubing sizes can be intermixed within each occlusion bed as long as the same tubing material is used. Use only MASTERFLEX two-stop tubing sets (Figure 4) withMASTERFLEX multichannel tubing pumps to ensure optimum performance. Use of other tubing may void applicable warranties.
4.3 TUBING REMOVAL Follow this procedure to unload the tubing: 1. Turn the drive OFF. 2. Unlatch and open occlusion bed. 3. Pull tubing down from slot to release tubing stop collar (Figure 9). 4. Release tubing stop collar from corresponding slot from other side.
Never immerse or required single channel flow rate. use excessive fluid. See Appendix B (Page 8) for ordering information on the 6.1 SERVICE PARTS MASTERFLEX Two-Stop Pump Tube Sets. Hex Key (9/64-in. hex) 5.2 SELECT PUMP SPEED Model 07534-04, 07535-04, 07536-02 A-3502...
TUBE SETS 3.9 lb (1.8 kg) (See page 8.) 8. WARRANTY Use only MASTERFLEX tubing sets with MASTERFLEX pumps to ensure optimum performance. Use of other tubing may void applicable warranties. The Manufacturer warrants this product to be free from significant deviations from published specifications.
Seite 8
Precision 07536-04 TYGON ® VITON ® * Number of channels may be achieved by stacking any combination of 2, 4, or 8 channel heads. Appendix B — MASTERFLEX Two-Stop Tube Sets Material Tubing Type Tubing Size Silicone ® ® SANTOPRENE...
Seite 10
10. Assistance technique............7 11. Annexe A Capacité de charge du tube ......7-8 12. Annexe B Ensembles de tubes ® MASTERFLEX à deux butées ........7-8 Figure 1. Têtes de pompe SÉCURITÉ AVERTISSEMENT : Les ruptures de tube peuvent entraîner l’écoulement du fluide hors de la pompe. Prenez des mesures appropriées destinées à...
4 canaux de tubes de précision microbore ou pompe avec la fente et les goupilles de positionnement à MASTERFLEX L/S ou jusqu’à 2 canaux de tubes de précision l’avant de la première tête de pompe. hautes performances MASTERFLEX L/S. Les têtes de pompe peuvent être empilées pour permettre jusqu’à...
Les tailles de tubes peuvent être mélangées au sein de chaque lit d’occlusion tant que le même matériau de tube est utilisé. Utilisez seulement les ensembles de tubes MASTERFLEX (Figure 4) avec des pompes multicanal MASTERFLEX pour assurer des performances optimales. L’utilisation d’autres tubes peut annuler la garantie.
4.3 ENLEVER LES TUBES Suivez la procédure suivante pour enlever les tubes : 1. COUPEZ l’entraînement. 2. Libérez le verrou et ouvrez le lit d’occlusion. 3. Tirez sur le tube depuis la fente pour libérer le collet de butée du tube (Figure 9). 4.
Ne pas immerger ou utiliser trop de liquide. Voir l’Annexe B (Page 8) pour les informations de commande 6.1 PIÈCES des ensembles de tubes de pompe MASTERFLEX. Clé hexagonale (9/64-in) 5.2 SÉLECTIONNER LA VITESSE DE Modèle 07534-04, 07535-04, 07536-02...
(Voir page 8.) 1.8 kg (3.9 lb) 8. GARANTIE Servez-vous uniquement de raccords de tuyau MASTERFLEX L/S pour assurer une performance optimale. L’utilisation d’autres tubes peut annuler la garantie. Le fabricant garantit que ce produit ne comporte aucune déviation significative des spécifications publiées. Pour toute réparation ou tout réglage pendant la période de garantie, le...
® VITON ® * Le nombre de canaux peut être atteint en empilant toute combinaison de têtes 2, 4 ou 8 canaux. ® Annexe B - Ensemble de tubes Masterflex à deux butées Matériau Type de tube Taille de tube Vulcanisation ®...
9. Rückversand ..............7 10. Technischer Kundendienst ..........7 11. Anhang A Max. zulässige Anzahl an Schläuchen ..7-8 ® 12. Anhang B Masterflex Schlauchsätze mit 2 Stoppern ..7-8 Abbildung 1, Pumpenköpfe SICHERHEITSHINWEISE WARNUNG: Ein Schlauchbruch kann zu Schäden durch austretende Medien führen. Treffen Sie geeignete Maßnahmen, um Bedienperson und Ausrüstung vor Beschädigung zu schützen.
Die vorliegende Bedienungsanleitung wurde nach Aufgaben Benötigtes Werkzeug: Innensechskantschlüssel, lang gegliedert, um Ihnen das Auffinden der gesuchten (inbegriffen) Informationen zu erleichtern. Sie können den betreffenden Um den Pumpenkopf an einem Masterflex ® L /S ® Abschnitt direkt aufschlagen. Er enthält alles, was Sie wissen müssen.
Abhängig von der Art des eingesetzten Pumpenkopfs können bis zu 8 Schlauchsätze in einem einzigen Pumpenkopf verwendet werden. In jedem Schlauchbett können verschiedene Schlauchgrößen kombiniert werden, vorausgesetzt, alle Schläuche sind aus dem gleichen Material. Verwenden Sie in Masterflex ® Mehrkanal-Schlauchpumpen ausschließlich Masterflex ®...
4.3 ENTFERNEN DES SCHLAUCHS Um einen Schlauch herauszunehmen, gehen Sie wie folgt vor: 1. Antrieb AUS schalten. 2. Schlauchbett entriegeln und öffnen. 3. Schlauch nach unten ziehen, damit der Stopper sich löst (Abbildung 9). 4. Schlauchstopper aus dem entsprechenden Klemmschlitz auf der anderen Seite nehmen.
Förderrate pro Kanal auszuwählen. verwenden. Tauchen Sie das Gehäuse auf keinen Fall in die Reinigungsflüssigkeit ein. In Anhang B (Seite 8) finden Sie Bestellinformationen für die in Masterflex ® Pumpen zu verwendenden Schlauchsätze mit 2 6.1 SERVICE- UND ZUBEHÖRTEILE Stoppern.
12. ANHANG B 07536-04 1,8 kg MASTERFLEX ® SCHLAUCHSÄTZE 8. GARANTIEERKLÄRUNG MIT 2 STOPPERN Verwenden Sie in Masterflex ® Pumpen ausschließlich (Siehe Seite 8). Masterflex ® Schlauchsätze, um eine optimale Leistung zu gewährleisten. Bei Verwendung anderer Schläuche kann die Garantie unwirksam werden.
07536-04 Tygon ® Viton ® * Die Anzahl an Kanälen wird erreicht durch Aneinandersetzen einer beliebigen Kombination aus Pumpenköpfen mit 2, 4, oder 8 Kanälen. ® Anhang B – Masterflex Schlauchsätze mit 2 Stoppern Material Schlauch typ Schlauchgröße Silikon ®...
8. Garantía ................7 9. Devolución del producto..........7 10. Asistencia técnica ............7 11. Apéndice A Capacidad de carga de los tubos ..7-8 12. Apéndice B Sets de tubos de dos topes Masterflex ® ..7-8 Figura 1, Cabezales de bombeo MEDIDAS DE SEGURIDAD ADVERTENCIA: Si se dañan los tubos, puede ocurrir que la bomba pierda fluido.
Instrumento necesario: llave larga hexagonal (provista junto función de las tareas para facilitar su consulta. Se puede ir con el equipo). directamente a una sección en particular y encontrar las Conecte el cabezal de bombeo al impulsor Masterflex ® L /S ®...
Se pueden mezclar varios tamaños de tubos dentro de cada asiento de oclusión siempre y cuando los tubos utilizados sean del mismo material. Utilice solamente sets de tubos de dos topes Masterflex ® las bombas Masterflex ®...
4.3 REMOCIÓN DE LOS TUBOS Siga este procedimiento para quitar los tubos: 1. Apague el impulsor (OFF) 2. Suelte la traba y abra el asiento de oclusión. 3. Tire del tubo hacia abajo hasta sacar el anillo de la ranura. (Figura 9).
único requerido. detergente suave. Nunca utilice excesivo fluido ni lo sumerja. Si desea información para ordenar tubos de dos topes 6.1 REPUESTOS Masterflex ® , consulte el Apéndice B (página 8). Llave hexagonal (9/64 pulg. hex.) 5.2 SELECCIÓN DE VELOCIDAD DE...
122 mm x 115 mm x 75 mm (Ver página 8.) 07536-04 (4.8"L x 4,5"An x 3"Al) 1,8 kg (3,9 lb) 8. GARANTÍA Utilice solamente sets de tubos Masterflex con las bombas ® Masterflex ® para asegurar un rendimiento óptimo. El uso de otros tubos puede dejar sin efecto las garantías vigentes.
® Viton ® * La cantidad máxima de canales se logra apilando cualquier combinación de 2, 4 u 8 cabezales. ® Apéndice B — Sets de tubos de dos topes Masterflex Material Tipo de tubo Tamaño de tubo Silicona Santoprene ®...
10. Assistenza tecnica ............7 11. Appendice A Tipi di motori per pompe Masterflex ® ® ..7-8 12. Appendice B Set di tubi a doppio stop Masterflex ® ..7-8 Figura 1: Teste pompanti MISURE DI SICUREZZA AVVERTENZA: La rottura di un tubo potrebbe provocare la fuoriuscita di liquido dalla pompa. Adottare le dovute precauzioni per proteggere il personale addetto e l’apparecchio.
2. Remuovere il piedino di supporto regolabile dalla testa precisione che sono stati costruiti a macchina. Gli sportelli di pompante. chiusura sono stati progettati per comprimere i tubi Masterflex 3. Allineare la linguetta e i fori presenti nella parte posteriore per l’ottenimento di prestazioni ottimali e richiedono alcuna della seconda testa pompante con la fessure e i perni di regolazione.
All’interno di ogni chiusura possono essere inseriti tubi di dimensioni differenti ma devono essere sempre dello stesso materiale (figura 4). Per ottenere prestazioni ottimali si consiglia l’associazione di tubi e pompe Masterflex. L’uso di tubi diversi da quelli espressamente indicati potrebbe essere motivo di decadenza della garanzia. Collare...
4.3 RIMOZIONE DEI TUBI Si prega di seguire le istruzioni seguenti per rimuovere i tubi: 1. Spegnere il motore; 2. Sganciare e aprire lo sportello della chiusura; 3. Tirare i tubi verso il basso dalla fessura per liberare il collare di blocco dei tubi (figura 9); 4.
Non immergere mai e non usare fluidi in quantità eccessive. Per ulteriori informazioni relative all’ordinazione dei tubi a doppio stop per pompe Masterflex ® consultare l’appendice B 6.1 PARTI DI RICAMBIO (Pagina 8).
(vedere pagina 8). 8. GARANZIA Per prestazioni ottimali, si consiglia, l’associazione di tubi e pompe Masterflex. L’uso di tubi diversi da quelli espressamente indicati potrebbe essere motivo di decadenza della garanzia. Il produttore garantisce che questo prodotto non differisce in maniera significativa dalle specifiche tecniche pubblicate.
® Viton ® * Il numero di canali può essere raggiunto allineando una combinazione qualsiasi di 2, 4, o 8 canali di teste pompanti. Appendice B — Set di tubi a doppio stop Masterflex ® Materiale Tipi di tubi Dimensioni...