Troubleshooting; Technical Specification - Somogyi Elektronic SF 41 Bedienungsanleitung

2. Afterwards screw on the grid fastening nut (5).
3. Place the fan blade (4) on the spindle, then fasten it with blade fastening screw (3).
4. Attach the front grill (2) to the rear part, and tighten it with the bolt (1) to fastening grid parts.
5. Place the assembled fan on the stand, and fasten it with the screw (10).
FEATURES
40 cm fan blade diameter • adjustable output (3 stages) • fixed standing or oscillation (85°) • adjustable height (110-130 cm) • controllable dip angle
of head • dense grid • white
Figure 1.
1. bolt for fastening grid parts • 2. front part of grid • 3. blade fastening screw • 4. fan blade • 5. grid fastening nut • 6. rear part of grid • 7. motor • 8.
speed level switches • 9. switch of oscillation • 10. fixing screw • 11. upper part of stand • 12. height fixing screw • 13. lower part of stand • 14. cover
piece • 15. base, consisting of two parts • 16. base fastening screws • 17. fixing screw for head dip angle
OPERATING FAN
Ventilator can be switched on with 1, 2 or 3 speed level switches (8) and target speed can be set as well. Oscillation can be turned on by pressing (9)
oscillation switch down, and can be turned off by pulling it up. You can switch off the fan with 0 button.
Dip angle of fan head part can be adjusted from the horizontal position with +/- 15° up or down. For that, loosen the screw (17), set the desired dip
angle, and then fasten the screw.
CLEANING
In order to ensure optimum functioning, the unit may require cleaning at least once a month, depending on the manner of use and degree of
contamination.
1. Prior to cleaning switch off and power off the unit by unplugging it from the electric outlet!
2. Attention! Remove the front part of grid when the fan is not under power!
3. Use a slightly moistened cloth to clean the unit's exterior. Do not use any aggressive cleaners. Avoid getting water inside of and on the electric
components of the appliance!
4. Attention! Put back and fasten the protective grid to the fan, when it is not under power!
5. Only reinstall the fan afterwards!

TROUBLESHOOTING

Malfunction
The fan doesn't turn on.
The fan does not oscillate.
Waste equipment must not be collected separately or disposed of with household waste because it may contain components hazardous
to the environment or health. Used or waste equipment may be dropped off free of charge at the point of sale, or at any distributor which
sells equipment of identical nature and function. Dispose of product at a facility specializing in the collection of electronic waste. By doing
so, you will protect the environment as well as the health of others and yourself. If you have any questions, contact the local waste
management organization. We shall undertake the tasks pertinent to the manufacturer as prescribed in the relevant regulations and
shall bear any associated costs arising.

TECHNICAL SPECIFICATION

power supply:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 30 V ~ / 50 Hz / 45 W
protection class: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II.
maximum fan - air mass volume . . . . . . . . . . . . . . . . . F = 50,0 m /min
fan input power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P = 45,0 W
service value: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SV = 1,111 (m /min)/W
power consumption during standby position: . . . . . . . P = 0,0 W
fan acoustic power level:. . . . . . . . . . . . . . . . . . . . . . . L = 67 dB(A)
maximum air speed: . . . . . . . . . . . . . . . . . . . . . . . . . . c = 2,9 m/sec
service value standard: . . . . . . . . . . . . . . . . . . . . . . . IEC 60879:1986 (corr. 1992)
length of power cable:. . . . . . . . . . . . . . . . . . . . . . . . . 1,5 m
blade diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 cm
ventilator height (adjustable): . . . . . . . . . . . . . . . . . . . 110 – 130 cm
ventilator weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,8 kg
Possible solution
Check the power supply.
Check the switches.
Check the switch of oscillation.
3
SB
WA
3