Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Pre-wash
The function is provided for washing of heavily soiled (very dirty) cotton items. When switching the
function on, the items will be washed additionally in the water with detergent at the temperature
of 30 ºC. It ensures a high quality dirt removal during the basic wash.
Additional rinse
The function is provided for washing children's clothes, items of people, who are detergent
allergic, or for washing in a very soft water, in which a detergent is rinsed insufficiently. When the
function is included into the Wash Program, one more rinse will be added.
Light press
he function is provided to reduce the creasing level of fabrics during washing and spinning and
to ease subsequent ironing. The function ensures a delicate washing mode and careful spinning
with minimum number of wrinkles after washing.
Stop with water in the tank
The function is used, when items of a fine texture are washed, and when there is no possibility to
take items from the Machine immediately after washing, not to get them crumpled. When the fu-
nction is switched on, the Machine will stop automatically after the last rinse (before water drain).
SOUND ALARM TURN ON/OFF
To turn off the machine operation sound alarm, simultaneously press the buttons
To turn off the machine operation sound alarm, simultaneously press the buttons
To turn off the machine operation sound alarm, simultaneously press the buttons
To turn off the machine operation sound alarm, simultaneously press the buttons
To turn off the machine operation sound alarm, simultaneously press the buttons
hold during 3 seconds. To turn the sound alarm on, press the buttons
ANTI-CLOSING DOOR BLOCKING
The anti-closing door blocking prevents from accidental Machine
operation, for example, by children. To lock the door, turn the lock (Fig.
Lock
4) by a screwdriver clockwise up against the stop – the lock will move
forward and prevent to close the door. To cancel the locking before
washing, perform all the actions in the reverse sequence.
Door
Figure 4
3 PREPARATION FOR OPERATION
PREPARATION FOR INSTALLATION
ATTENTION! Not to damage the Machine, never move it by holding the dispenser drawer, door
or gasket.
For transportation purposes, the drum of the Machine is fixed by locking bolts and spacer bars. Unsc-
rew the four bolts with a spanner and take out the spacer bars (Fig. 5). If the spacer bars remain inside the
Machine and would not get out, remove the back panel 1 (Fig. 6) with a cross-blade screwdriver and take
the bars out. Reinstall the panel. Close the holes with plastic plugs, including in the kit. Keep the bolts and
spacer bars for future transportation.
NEVER operate the Machine with open spacer bar holes in the rear wall of the body.
INSTALLATION OF THE MACHINE
The Machine should be installed on a solid, even and dry surface. Soft flooring (carpets, polyurethane-
based coatings) is not recommended as it promotes vibration and degrades ventilation of the Machine.
When installed on a wooded floor, the Machine should be first placed onto a wooden slab at least
15 mm thick that is reliably bolted to the floor.
To increase the stability of the Machine during its operation on a wooden floor, it is recommended to
install the Machine in the corner of the room.
6
and
and
and
again.
1
Figure 5
Figure 6
The Machine should be levelled precisely horizontally by screwing its adjustable supports 1 in or out:
loosen lock nuts 2 of the supports with a spanner, adjust the height of the supports, and tighten the lock
nuts (Fig. 7). A wrong installation of the Machine by its horizontal level and low tightening of the lock nuts
may be in the future a source of vibration and excessive noise during its operation.
CONNECTING TO WATER SUPPLY AND DRAINAGE
Prior to connect the Machine to water supply, open the tap and let water flow and flush any sand and
rust from water supply pipes.
The Machine is connected only to the cold water supply system through a water supply tap with a
¾-inch threaded branch pipe.
Connect the filling hose to the threaded branch pipe of the water supply tap, having first checked the
presence of filter 1 (Fig. 8) in the hose and its clean condition, and to electric valve 1 (Fig. 9) of the Machine,
having tightly screwed the nuts manually.
If the filling hose has a protecting system in accordance with figure 8a, attention should be paid to
the colour in a special window of the hose. The yellow colour of the window shows the good state of
the hose.
In the process of washing, the water supply tap should be completely open (Fig. 10).
The draining hose (Fig. 11) should be at least 60 cm and at most 90 cm above the floor level. It this
requirement is not observed, the Machine would not work.
For draining water directly into the sewerage, the draining hose should be fixed above the sewerage
elbow (trap) into the sewerage pipe with internal diameter of at least 40 mm to avoid reverse suction of
drain water into the Machine.
The draining hose may be connected directly to the trap (Fig. 12), if it has a branch pipe for this pur-
pose.
When draining water into the sink or bath the hose (Fig. 13), fix the hose in the bending point by a
special clamp supplied with the Machine. The hose should not be immersed into water.
ATTENTION! After connecting to the water supply and sewerage, the filling and draining hoses
1
Figure 8
Figure 8a
1
2
Figure 7
1
1
Figure 9
7
Werbung
Inhaltsverzeichnis
