Makita 6805BV Betriebsanleitung Seite 5

18. Outdoor use extension cords
When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
19. Stay alert
Watch what you are doing. Use common sense.
Do not operate tool when you are tired.
20. Check damaged parts
Before further use of the tool, a guard or other
part that is damaged should be carefully checked
to determine that it will operate properly and per-
form its intended function. Check for alignment of
moving parts, binding of moving parts, breakage
of parts, mounting, and any other conditions that
may affect its operation. A guard or other part
that is damaged should be properly repaired or
replaced by an authorized service center unless
otherwise indicated elsewhere in this instruction
manual. Have defective switches replaced by
and authorized service center. Do not use tool if
switch does not turn it on and off.
21. Warning
The use of any other accessory or attachment
other than recommended in this operating
instruction or the catalog may present a risk of
personal injury.
22. Have your tool repaired by an expert
This electric appliance is in accordance with the
relevant safety rules. Repairing of electric appli-
ances may be carried out only by experts other-
wise it may cause considerable danger for the
user.
ADDITIONAL SAFETY RULES
1. Always be sure you have a firm footing. Be
sure no one is below when using the tool in
high locations.
2. Hold the tool firmly.
3. Keep hands away from rotating parts.
4. When driving into walls, floors or wherever
"live" electrical wires may be encountered,
DO NOT TOUCH ANY METAL PARTS OF THE
TOOL! Hold the tool by the insulated grasp-
ing surfaces to prevent electric shock if you
drive into a "live" wire.
5. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely
hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Removing or installing the bit (Fig. 1)
Important:
Always be sure that the tool is switched off and
unplugged before removing or installing the bit.
To remove the bit, first pull the front cap off and then
pull the bit firmly. To install the bit, insert it into the
tool as far as it will go and then replace the front cap.
Depth adjustment (Fig. 2, 3 & 4)
When you wish to drive self drilling screws, etc.,
adjust the depth as follows. Turn the locator to adjust
the depth.
Initially, adjust the locator to create a distance of
approximately 1 mm from the tip of the front cap
(which works in conjunction with the locator) to the
base of the screw head. One full turn of the locator
equals 1 mm change in depth. After adjusting the
locator, turn the adjusting ring so that the 6" mark is
aligned with the pointer on the gear housing. Drive a
trial screw into your material or a piece of duplicate
material. If the depth is not suitable for the screw,
continue adjusting until the proper depth setting is
obtained.
Adjusting fastening torque (Fig. 5)
When you wish to drive tool screws, wood screws,
hex bolts, etc. with the predetermined torque, adjust
the fastening torque as follows. The fastening torque
may be adjusted by turning the adjusting ring. Before
turning the adjusting ring, turn the locator in the
direction of the arrow as far as it will go without forc-
ing. The torque is increased by turning the adjusting
ring in the direction of the arrow and decreased by
turning it in the opposite direction. Align the number 1
on the adjusting ring with the pointer on the gear
housing. Drive a trial screw into your material or a
piece of duplicate material. If the fastening torque is
not suitable for the screw, continue adjusting until the
proper torque is obtained.
CAUTION:
The adjusting ring should be turned only within the
numbered range. It should not be forced beyond this
range.
Switch action (Fig. 6)
CAUTION:
Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger.
Release the trigger to stop. For continuous operation,
pull the trigger and then push in the lock button. To
stop the tool from the locked position, pull the trigger
fully, then release it. A speed control screw is pro-
vided so that maximum tool speed can be limited
(variable). Turn the speed control screw clockwise for
higher speed, and counterclockwise for lower speed.
NOTE:
Even with the switch on and motor running, the bit
will not rotate until you fit the point of the bit in the
screw head and apply forward pressure to engage
the clutch.
5