Wichtige Hinweise zur Bedienungsanleitung 1.1. Hinweise zur Bedienungsanleitung Vor Inbetriebnahme ist dieses Handbuch aufmerksam durchzulesen. Die Bedienungsanleitung enthält wichtige Funktionsweisen und Sicherheitsvorschrif- ten. Werden diese nicht beachtet, ist die bestimmungsgemäße Verwendung in explo- sionsgefährdeten Bereichen nicht gewährleistet. Bei der Inbetriebnahme und Verwendung des Produkts sind die Hinweise dieses Handbu- ches zu beachten.
1.3. Allgemeine Hinweise 1.3.1. Warnhinweise • Das Gerät darf nur im zusammengebauten Zustand betrieben werden. • Gerät im explosionsgefährdeten Bereich nicht trocken abwischen oder reinigen! • Das Gerät ist unverzüglich auszuschalten, wenn anzunehmen ist, dass es nach schädlichen Einwirkungen oder bei allgemeinen Auffälligkeiten nicht mehr gefahrlos betrieben werden kann (z.B.
1.3.4. Wartung Bei Beachtung der Montageanweisung, den Umgebungsbedingungen und einem sachge- mäßen Betrieb, ist keine ständige Wartung erforderlich. 1.3.5. Inspektion Der Betreiber muss ein elektrisch betriebenes Gerät im explosionsgefährdeten Bereich durch eine Elektrofachkraft auf seinen ordnungsgemäßen Zustand prüfen lassen (IEC 60079-17 und IEC 60079-19).
Hersteller PRIMATION Systemtechnik GmbH & Co. KG Bretonischer Ring 13 85630 Grasbrunn Deutschland 2.1.1. Gerätetypen P-Ex WLAN-DC-A P-Ex WLAN-DC-S 2.2. Explosionsschutz I M2 Ex eb qb [ib] I I M2 Ex e q [ib] I Mb II 2G Ex eb qb [ib] IIC T4 II 2G Ex e q [ib] IIC T4 Gb II 2D Ex tb IIIC T135°C...
Inbetriebnahme des P-Ex WLAN Access Point 3.1. Informationen zum Aufbau des P-Ex WLAN Durch die vier Befestigungsbohrungen an den Ecken der Grundplatte wird die Montage auf sicherem Untergrund erleichtert. Die Bohrungen haben einen Durchmesser von 7mm. Die PA Bohrungen der Erdungsschrauben befinden sich jeweils an der Vorder- und Hinterkante der P-Ex WLAN Grundplatte.
3.2. Bedeutung der Leuchtdioden Alle Leuchtdioden sind erst nach Software-Einstellung und Reboot im korrekten Betrieb. LED blinkt LED leuchtet Power Gerät ist gestartet LAN LINK Datenübertragung aktiv Schnittstelle bereit WLAN LINK Datenübertragung aktiv Schnittstelle bereit Die Leuchtdioden USER 1 und USER 2 sind in der Standardkonfiguration ohne Funktion. Diese LEDs können im Menü...
Betriebsspannung +18V bis +28V DC Leiterquerschnitt flexibel -0,2 mm – 1,3 mm / 24AWG – 16AWG Leiterquerschnitt starr -0,2 mm – 1,3 mm / 24AWG – 16AWG Es darf maximal 1 Leitung pro Klemme angeschlossen werden. Schrauben mit einem Dreh- moment von 0,5Nm anziehen.
3.5. Sendesignal der RP-SMA Steckverbinder des P-Ex WLAN RP-SMA Steckverbinder – Belegung Ex i RP-SMA 1 Sendesignal 1 RP-SMA 2 Sendesignal 2 Die Frequenz beträgt 2,4GHz / 5GHz Die Ausgangsleistung beträgt ≤ 312mW Für den P-Ex WLAN dürfen ausschließlich die Antennen mit der Typnummer ANT-24/58-3/5- I, ANT-24-7-I, ANT-24-8-O, ANT-24-2-O verwendet werden.
4.2.2. Quick Setup Mittels Webbrowser kann die Verbindung zum P-Ex WLAN Access Point hergestellt werden. Die IP Adresse des Gerätes muss hierzu in die Adresszeile des Browsers eingegeben wer- den. Auf der ersten Seite des Konfigurationsmenüs können die Grundeinstellungen vorge- nommen werden.
Eine ausführliche Bedienungsanleitung für das Betriebssystem „RouterOS“ kann jederzeit unter http://wiki.mikrotik.com heruntergeladen werden. Hier gibt es auch die Möglichkeit häu- fig benötigte Kapitel in einem PDF zusammenzufassen und dauerhaft abzuspeichern. 4.3. Konfiguration mit Winbox Mit der Software Winbox kann der P-Ex WLAN von jedem Windows-Rechner aus konfiguriert werden.
Seite 15
Wenn die Verbindung über die IP Adresse nicht möglich ist, weil sich der P-Ex WLAN in ei- nem anderen IP-Netz befindet, so kann mittels anklicken der MAC Adresse eine Verbindung auf MAC Basis aufgebaut werden. Diese ist etwas langsamer als die Verbindung mittels IP Adresse, reicht aber aus um die Grundeinstellungen am P-Ex WLAN vorzunehmen und die- sen ins korrekte IP-Netz zu bringen.
Eine Anleitung in der die Möglichkeiten der Winbox detailliert erläutert werden ist unter http://wiki.mikrotik.com/wiki/Winbox einsehbar. Die Basiseinstellungen des P-Ex WLAN erfolgen ebenfalls mittels der Quick Sets wie unter 4.2.2 beschrieben. Zubehör P-Ex WLAN 5.1. Übersicht Zubehör Frequenz- Antennen- Bezeichnung Länge Einsatzbereich bereich GHz gewinn dBi...
Seite 17
• Rundstrahl Antenne für den Außenbereich (ANT-24-8-O) Vertikalrundstrahler für den 2,4 GHz Bereich mit 8 dBi Antennengewinn und einer Länge von 64 cm. Wetterfeste Ausführung für den Außenbereich, aber auch ideal für die Versorgung von Innenräumen, z.B. im Treppenhaus. Der Strahler ist gleichspannungsmäßig geerdet um statische Aufladungen zu verhindern.
User manual WLAN access point Type P-Ex WLAN-DC-A Type P-Ex WLAN-DC-S ATEX Version Zone 1/21/M2 Version: Drafted: 08/02/2017 Subject to technical changes! Contents Page German 1-18 English 19-37 PRIMATION Systemtechnik Tel: +49 (0) 89 46 26 0 - 0 GmbH & Co. KG...
Seite 23
Contents Important instructions for use ....................20 1.1. Instructions for use ......................20 1.2. Pictograms and safety guidelines..................20 1.3. General warnings ......................21 Product information ........................23 2.1. Manufacturer ........................23 2.2. Explosion protection ......................23 2.3. Technical data ........................23 2.4.
1. Important instructions for use 1.1. Instructions for use Please read this manual through carefully before using the device. This user manual contains information about key functions and safety precautions. If they are not observed, no guarantee is given that the device can be used in potentially explosive environments, for which it is intended.
1.3. General warnings 1.3.1. Warnings • The device may only be operated when fully assembled. • Do not wipe with a dry cloth or clean the device in a potentially explosive environment! • The device must be immediately shut down if you have reason to suspect it cannot run any- more without causing harm or endangering people (e.g.
Seite 26
1.3.5. Inspection The operator must have any electrical device that is intended for use in potentially explosive environments tested by a specialized electrician to check it is in good working order (IEC 60079-17 and IEC 60079-19). 1.3.6. Repairs Repairs may only be carried out by the manufacturer or any person who has been trained and tasked to carry them out.
Manufacturer PRIMATION Systemtechnik GmbH & Co. KG Bretonischer Ring 13 85630 Grasbrunn Germany 2.1.1. Device types P-Ex WLAN-DC-A P-Ex WLAN-DC-S 2.2. Explosion protection I M2 Ex eb qb [ib] I I M2 Ex e q [ib] I Mb II 2G Ex eb qb [ib] IIC T4 II 2G Ex e q [ib] IIC T4 Gb II 2D Ex tb IIIC T135°C...
Outdoors ≤ 50km (depending on the antenna) Range for copper cat. 5 100m Dimensions 150mm x 270mm x 60mm (HxWxD) Weight Type P-Ex WLAN-DC-A 3.3kg (aluminum) Type P-Ex WLAN-DC-S 4.5kg (V2A stainless steel) Atmospheric temperature -20°C to +60°C 2.4. Type numbers...
Operating the P-Ex WLAN access point 3.1. Assembly information for the P-Ex WLAN The bottom plate has four drilled holes, one on each corner, which facilitate securely mounting the device. The holes have a di- ameter of 7mm. The PA drill holes for the earthing screws are at the front and back edges of the P-Ex WLAN bottom plate.
3.2. LED signals All LEDs only run correctly once the software has been correctly set up and the device has been rebooted. LED flashing LED on Power Device has booted LAN LINK Data transfer is active Interface ready WLAN LINK Data transfer is active Interface ready The USER 1 and USER 2 LEDs have no preset function.
Operating voltage +18V to +28V DC Conductor cross-section flexible -0.2 mm – 1.3 mm / 24AWG – 16AWG Conductor cross-section rigid -0.2 mm – 1.3 mm / 24AWG – 16AWG A maximum of 1 conductor per clamp may be connected. Tighten the screws with a torque of 0.5Nm.
3.5. Transmission signal of RP-SMA plug connector of the P-Ex WLAN RP-SMA plug connector - Assignment Ex i RP-SMA 1 Transmission signal 1 RP-SMA 2 Transmission signal 2 The frequency is 2.4GHz/5GHz The output level is ≤ 312mW Only ANT-24/58-3/5-I, ANT-24-7-I, ANT-24-8-O, ANT-24-2-O type antennas may be used with the P-Ex WLAN.
3.7. Color coding of the cat-cable/ethernet cable Allocation of the cat-cable/ethernet cable and LSA+ module clamps according to EIA/TIA T568A PIN LSA+ module clamp Cat-cable color code 100BaseT assignment X10-4 WHT/BLU X10-5 X10-7 WHT/BRN X10-8 X11-1 WHT/GRN X11-2 X11-3 WHT/ORG X11-6 Allocation of the cat-cable/ethernet cable and LSA+ module clamps according to EIA/TIA T568B...
Seite 34
4.2.2. Quick Setup You can set up a connection with the P-Ex WLAN access point via a web browser. To do this, copy the device's IP address into the browser address bar. On the first page of the con- figuration menu you can set up the basic settings. As per the factory settings, the P-Ex WLAN shows up as "Access Point - Bridge"...
A detailed instruction manual for the operating system "RouterOS" can be downloaded from http://wiki.mikrotik.com at any time. When visiting this website, you also have the option of downloading any really useful chapters as a PDF, which you can then save on your comput- er for future reference.
Seite 36
If the connection cannot be made via the IP address because the P-Ex WLAN is connected to a different IP network, you can click on the MAC address to use the MAC method to set up a connection. This is somewhat slower than the connection via IP address but is sufficient to configure the P-Ex WLAN's basic settings and transfer these into the correct IP network.
To see a guide on all the different functions Winbox offers, go to http://wiki.mikrotik.com/wiki/Winbox. The basic settings of the P-Ex WLAN can be configured via the Quick Set function as de- scribed in 4.2.2. P-Ex WLAN accessories 5.1. Accessories overview Frequency- Antenna Operating...
Seite 38
• Omni-directional antenna IP68 (ANT-24-2-O) Water-proof, short, screw-in antenna for the 2.4 GHz frequency range with an antenna gain of 2 dBi and a length of 9.2cm. The antenna is connected to the access point via a 150 cm extension cable. •...